Talk Electronics
Thunder 1.2 CD Player
User Manual
TALK ELECTRONICS LTD. UNIT 3 IMAGE HOUSE 326 MOLESEY ROAD HERSHAM SURREY KT12 3PD ENGLAND
SWITCHING YOUR CD PLAYER ON AND OFF
NOTE: These instructions apply in the United
Kingdom only – consult your dealer about wiring
conventions in other countries.
If you are using a Whirlwind external DC supply to
power the analogue parts of your CD player we
suggest that this, once connected, is left switched
on all the time. To avoid “switch-on thumps” being
transmitted to your loudspeakers when you switch
on your CD player, we recommend that you always
switch on – or cancel mute on – your amplifier last.
Start by powering source components, such as your
CD player, then power the pre-amplifier. Then switch
on the power amplifier. When you’ve finished
listening, mute or turn off the power amplifier and
then mute your pre-amplifier. Finally, turn off your CD
player and other source components. You may, if
you wish, leave your CD player powered up at all
times: this will enable it to deliver optimum
Green and yellow wire connects to EARTH (E or
symbol
)
Blue wire connects to NEUTRAL (N)
Brown wire connects to LIVE (L)
Please ensure that the replacement lead contains a
5A fuse.
OPTIONAL DC POWER CONNECTIONS
If you have opted for one of our external Whirlwind
DC power supplies this should be connected using
only the cables supplied with the Whirlwind. We
strongly recommend that you do not replace or
attempt to modify these cables. Doing so can
adversely affect the CD player’s performance and is
likely to cause damage.
performance as soon as you begin listening,
however we suggest that you switch off the display
when not required. This requires that a disc is
present in the player at all times.
The power switch mounted on the Thunder’s rear
connects and disconnects the mains supply. When
mains is connected, the display on the facia will
illuminate. If you plan to be away from home for long
periods – when, for example, you are on holiday –
you can use this switch to power down the CD
player completely. For absolute safety, disconnect
the mains lead from the wall socket. We advise that
you do this during thunderstorms to avoid damage
from power line surges.
You will also need to re-configure your player for
external DC operation using the internal jumpers as
described below.
DIAGRAM 1. INTERNAL/EXTERNAL JUMPER POSITIONS
External DC socket
Rear Panel
REAR PANEL
MAINS CONNECTIONS
Next to the mains switch, on the rear panel, is an
IEC socket into which the supplied mains lead fits.
The fuse in the UK mains plug is a 3A standard type.
Again, if you need to replace it use an identical type
rated at 3A. If the fuses keep blowing return the CD
player to your dealer.
OUTPUT CONNECTIONS
The analogue output sockets on the CD player are
found on the rear panel. Connect these to your
amplifier or pre-amplifier’s CD input using high quality
interconnect cables (we strongly recommend Merlin
cables for optimum performance). On all players, the
socket marked in red is the right channel, and the
white socket is the left channel.
Before attempting to re-configure your player,
disconnect the mains lead at the wall socket.
Having made your player safe, remove the cover
by unscrewing the five screws located on the rear
and the four on the underside. The cover slides off
backwards. Locate the blue jumpers using the
diagram above (Diagram 1.) and position them for
the desired configuration. Replace the cover,
connect your Whirlwind power supply and re-
connect the mains lead to the wall socket.
There are digital outputs as standard on all our
players. Our research shows that the levels of signal
jitter caused by separating the player’s transport
mechanism and DAC introduce an unacceptable
degradation in sound quality, counteracting the
benefits accrued through using our high quality,
ultra-low jitter, 24-bit DAC. If you wish to make digital
recordings you will need to switch on the digital
output provided using the yellow internal jumper, see
Diagram 2. However, we caution you that this
addition will have a slight detrimental effect upon the
player’s performance.
PLAY/PAUSE: Push once to start the disc playing. If
the player’s drawer is open, pushing play will cause it
to close and commence playing automatically.
Pressing for a second time whilst playing a disc will
pause the disc.
Optical Digital Output
Analogue Outputs
REPEAT: Push once to repeat the whole disc. Push
twice to repeat the track currently playing. Pressing
the button a third time returns normal operation.
Rear Panel
STOP: Push once to stop the player operating.
PREVIOUS: Push during Play mode to play the
previous track. Pushing more than once will cause
the player to go back an equivalent number of
tracks.
NEXT: Push during Play mode to play the next track.
Pushing more than once will cause the player to
advance an equivalent number of tracks.
TIME: Push once during Play mode to display the
time remaining on the current track. Push again to
display the time remaining on the disc. Push while
the player is in Stop mode to display the total
number of tracks and playing time of the disc.
Note: if the disc contains more than 69 tracks the
display will show “_ _ . _ _” instead of the remaining
time. It will show the same if the remaining time
exceeds 100 minutes during PROGRAM PLAY
mode.
DISPLAY: Push once to turn off the display. Push
again to return the display to full brightness.
Jumper
DIAGRAM 2: SP/DIFF OUTPUT SELECTION
Note: When the display is switched off, pushing any
control on the player or remote handset, or changing
the disc, will switch on the display for about 3
seconds. Please note that this function only works if
a disc is present in the player and playing.
Before attempting to re-configure your player,
disconnect the mains lead at the wall socket.
Having made your player safe, remove the cover
by unscrewing the five screws located on the rear
and the four on the underside. The cover slides off
backwards. Locate the yellow jumper using the
diagram above (Diagram 2.) and position it for the
desired configuration. Replace the cover and re-
connect the mains lead to the wall socket. The
Digital Output should now work accordingly.
REMOTE CONTROL FUNCTIONS
As well as duplicating the major controls found on
the player, the remote handset provides the following
additional features.
PROGRAM: push to construct a program
containing up to twenty-four selected tracks. The
player will play your selections in the order in which
you enter them into the program.
OPERATING YOUR CD PLAYER
You can control the major functions of your CD
player from either the remote control handset or the
buttons on the player’s facia. If you simply wish to
play a disc you do not need the remote control.
However, do not lose the handset because it is
required when you wish to program the player or use
features such as FF or FR.
1. Select a track number by pressing the PREVIOUS
or NEXT key, or by using the numerical keys.
2. Press PROGRAM. “PROGRAM” appears on the
display panel indicating Program Play mode.
3. To add further tracks repeat steps 1 and 2.
Once you have entered all the desired tracks, you
can play your programme by pressing the PLAY
button
PLAYER CONTROLS
OPEN: Push once to close the player’s drawer after
inserting a disc. Do not push the drawer closed with
your hand as this can damage the drawer
mechanism.
To erase a programmed track, press the CLEAR key.
Each time you press CLEAR, the last selection in the
program will be removed. Press STOP to stop the
program playing, then press STOP again.
FAST FORWARD and REWIND: To move rapidly to
a particular section of music you can use the FAST
FORWARD or REWIND keys, depending, obviously,
upon whether you wish to access a section not yet
reached or one that you have passed. While the
player is in Play mode you will hear music playing at
high speed. To move quickly through the disc in
silence, press PAUSE before pushing the FF or REW
buttons.
TIMER MODE
Your player is equipped with a Timer Mode. This
allows the player to automatically play a disc when
powered on from the mains via the use of an exter-
nal timer. It is switched off by default at the factory.
To turn this on follow the instructions below using
Diagram 3
.
View of bottom right
corner of main PCB
NUMERIC KEYS: These are used for entering
selections in Program mode or for starting Play
mode from a particular track. For example, loading a
disc and then pressing “7” will cause the player to
start playing the disc beginning at track 7. To access
tracks greater than 9, first press “0” followed by the
track number required.
VOLUME: The volume buttons will operate the
volume function on any remote control amplifier that
accepts RC5 commands. They are provided solely
for your convenience, as there are no volume control
functions on the CD player
Timer jumper
HIDDEN MODES
These are only accessible with the use of an RC5
handset with the appropriate keys (Not the supplied
handset).
Main system micro
SHUFFLE: Press SHUFFLE followed by PLAY to
listen to tracks in a random order. To cancel Shuffle
mode, press SHUFFLE again.
INTRO: Press INTRO and the player will scan
through the disc playing the first 10 seconds of each
track. Press INTRO while in Play mode and the
player will scan through the disc playing the first 20
seconds of each track. To cancel either Intro mode
simply press PLAY.
Front Panel
DIAGRAM 3: TIMER OPTION
Before attempting to re-configure Timer Mode,
disconnect the mains lead at the wall socket.
Having made your player safe, remove the cover
by unscrewing the five screws located on the rear
and the four on the underside. The cover slides off
backwards. Locate the yellow jumper located in
the bottom right corner of the main PCB using
Diagram 3. above. To set the Timer ON remove the
yellow jumper or place it in such a way that it is
held by only one pin. Replace the cover and re-
connect the mains lead to the wall socket. The
Timer Mode should now be operational via the use
of an external mains power timer.
SPECIFICATIONS
Maximum Output Voltage
Output Impedance
THUNDER 1.2
2.3V RMS
<50 ohms
Frequency Response
Distortion 1kHz max output
Signal - to - Noise Awtd
Mains Voltage
5 – 20k ± 0.5dB
<=0.001%
–101dB
230V /115V/100V AC ± 10%
430mm
Dimensions
width
height
depth
82mm
300mm
(allow at least 400mm for connections)
6.2kg
7.6kg
Weight per unit unpacked
packed
Talk Electronics’ policy of continued research and development means that
the above specification may change without notice.
The Thunder has been manufactured to conform with the protection
requirements of the EC Council directive 89/336/EEC relating to EMC by
application of the following standards:
EN50081-1 1992 Emissions Standard
EN50082-1 1992 Immunity Standard
and also the requirements of the EC low voltage directive relating to electrical
safety by application of the following standard
BSEN60065: 1994 Safety standard
For the purposes of testing the Thunder was used with the mains cables and
high quality interconnects supplied by Merlin Cables. Compliance with the
above standards can only be made if the unit is installed as per this manual
and using the correct cables.
*Guarantee: 3 Years return to dealer.
To help us provide you with the most efficient service please return your
guarantee card promptly. Your CD player is guaranteed against manufacturing
and component defects for a period of 3 years. The guarantee does not cover
and damage caused by accident, misuse, neglect or through incorrect
installation, adjustment or repair by unauthorised personnel or the cost of
collecting the Thunder from you and returning it to the dealer. The above does
not effect your statutory rights as a consumer.
E & OE. Due to our policy of continued development we reserve the right to
change the specifications at any time.
*Upon return of Guarantee Card
Talk Electronics
TALK ELECTRONICS LTD. UNIT 3 IMAGE HOUSE 326 MOLESEY ROAD HERSHAM SURREY KT12 3PD ENGLAND
GUARANTEE
To extend your guarantee from 1 year to 3 years FREE of charge please complete and return this form
TALK ELECTRONICS LTD.
UNIT 3 IMAGE HOUSE
326 MOLESEY ROAD
HERSHAM
SURREY KT12 3PD
ENGLAND
FOLD HERE
Model: Thunder 1.2
Please tell us about the rest of your system
Amplifier ________________________________
Tuner ___________________________________
Speakers ________________________________
Mains Cables ____________________________
Interconnect Cables ______________________
Speaker Cables __________________________
Purchase date ___________________________
Price paid _______________________________
Serial Number____________________________
Colour:
■Black
■
Silver
Where did you purchase your Thunder 1.2?
________________________________________
Why did you choose the Thunder 1.2?
________________________________________
________________________________________
How did you hear about Talk Electronics?
■
■
■
Existing customer
Family/Friend
Advertising
Are you interested in Home Cinema?
■
■
Dealer
■
Yes
■
No
■
Undecided
Review
■
Internet
Other ___________________________________
Have you visited our website?
■
Yes
■
No
■
Do not have connection
FOLD HERE
Customer Name __________________________
Comments_______________________________
________________________________________
________________________________________
________________________________________
________________________________________
________________________________________
________________________________________
________________________________________
________________________________________
Address _________________________________
________________________________________
________________________________________
Post Code _______________________________
E-mail address ___________________________
Data Protection Act
Your details will be held by Talk Electronics Ltd. for promotional and
statistical purposes.
■
If you do not wish to receive marketing information please tick this box
|