Ericsson G30 / G35
Fixed Wireless Terminal for GSM Mobile Networks
User Guide
Table of Contents
Table of Contents
Table of Contents ..............................................3
Welcome...........................................................4
Fixed Wireless Terminal .....................................6
Installation .........................................................9
Connecting Devices to the FWT.......................15
Advanced Features..........................................20
Troubleshooting...............................................28
Technical Data.................................................32
Accessories.....................................................35
Product Care and Safety..................................37
Warranty..........................................................41
Glossary..........................................................43
Index ...............................................................45
Fixed Wireless Terminal: G30 and G35 models
3
Welcome
Welcome
Welcome to the User Guide for the G30 / G35 Fixed Wireless Terminal.
Important information: Some of the services described in this
guide might not be supported by all networks. Please, contact your
network operator for information on different network services
operational in your GSM network.
The latest version of this user guide can be downloaded from:
Disposal of the product
Your product should not be placed in municipal waste. Please check local
regulations for disposal of electronic products.
4
Fixed Wireless Terminal: G30 and G35 models
Welcome
Copyright
No part of this document may be reproduced without the written
permission of the copyright owner.
The contents of this document are subject to revision without notice due
to continued progress in methodology, design and manufacturing.
Ericsson shall have no liability for any error or damage of any kind resulting
from the use of this document.
Warranty
ERICSSON MAKES NO WARRANTY OF ANY KIND WITH REGARD TO
THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. Ericsson shall not be liable for errors contained
herein nor for incidental or consequential damages in connection with the
furnishing, performance or use of this material.
Declaration of Conformity
Hereby, Ericsson Enterprise AB declares that this product is in conformity
with the requirements and other relevant provisions of the European
R&TTE directive 1999/5/EC.
FCC Statement
Before a wireless terminal is available for sale to the public, it must be
tested and certified to the FCC that it does not exceed the limit
established by the government adopted requirement for safe exposure.
This device complies with CFR 47 Part 15 and Part 24 of the FCC rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may
cause undesired operation.
Fixed Wireless Terminal: G30 and G35 models
5
Fixed Wireless Terminal
Fixed Wireless Terminal
Product Description
The FWT is a flexible and cost-effective solution for connection to the
wireless GSM network when there is no fixed line infrastructure or if you
need additional telephone lines.
The G35 can also be connected to a PBX so you can benefit from the
Least Cost Routing (LCR) capabilities offered by most PBX vendors to
optimize your costs by routing outgoing calls to mobile phones through
the GSM network.
The FWT allows automatic network searching between GSM 850/1900 or
GSM 900/1800 frequencies, ensuring world wide coverage in the GSM
networks.
The FWT features the latest technology, which makes it perfect for
everyday communication:
•
Available in 2 dual-band GSM models (GSM 850/1900 or GSM
900/1800.
•
•
•
Telephone line providing high quality speech.
Battery back-up (optional).
PBX connectivity (only on the G35 model).
6
Fixed Wireless Terminal: G30 and G35 models
Fixed Wireless Terminal
Supplied Parts
After unpacking, please check that the following parts and list of
components are included:
List of Components
1. FWT unit
2. Antenna
3. 4 x mounting screws
4. Power cable (USA, UK, EU or AUS)
5. AC/DC adapter
6. Wall mount bracket
7. Telephone cable
8. Quick Guide and User Guide manuals
Fixed Wireless Terminal: G30 and G35 models
7
Fixed Wireless Terminal
External Connector and Indicators
8
Fixed Wireless Terminal: G30 and G35 models
Installation
Installation
SIM Card
Your network operator provides you with a SIM (Subscriber Identity
Module) card. The SIM card contains information about your telephone
number and the services included in your subscription.
Preparing Your FWT
You need to follow these steps before you install the FWT on the wall and
finalize all connections.
Warning: The FWT should be switched off before inserting or
removing your SIM card or connecting any devices to the FWT.
Assembly
1. Connect the antenna.
Fixed Wireless Terminal: G30 and G35 models
9
Installation
2. Remove the front cover, by pressing down and pushing the small tab
that is in the center of the bottom part of the FWT. Open the SIM
Card holder and insert the SIM Card.
3. Close the SIM Card holder, placing it horizontally and securing it with
the sliding part of the holder.
4. Install the battery (optional) in the battery compartment (over the SIM
Card). To do so, connect the battery cable to the FWT connector.
Connect the black cable to the negative pole (-) of the battery and the
red cable to the positive pole (+). Fit the cable under the holding tab
(over the SIM Card) and insert the battery until the tab fixates it.
5. Replace the front cover.
Connecting a telephone to the FWT
Connect an analog telephone to the line interface (RJ11) of the FWT.
Important: You may have to use this telephone to enter the PIN
code.
10
Fixed Wireless Terminal: G30 and G35 models
Installation
Switch on the FWT
Connect the power supply. The FWT switches on automatically and the
LED indicators start flashing.
Note: If the Power LED is off, there is a problem with the power
supply. Please refer to the topic Troubleshooting documented on
page 28 for more detailed information.
Enter PIN
Most SIM cards are protected with a PIN (Personal Identity Number),
which you get from your network operator and which you need in order to
access the network. If the SIM card is not protected by a PIN code, then
you do not need to enter a PIN.
The FWT starts the network search automatically. If the SIM card is
protected by the PIN code, then the LEDs will flash simultaneously.
Please follow these steps before you enter your PIN:
1. Pick up the telephone and dial the PIN code. Press the # key on your
telephone or wait until you hear a beep tone.
2. If you make a mistake while entering your PIN, hang up the telephone
and try again.
If the PIN is correct, you will hear a beep over the telephone (positive
indication tone). If it is incorrect, a deep tone will sound (error indication
tone).
If the PIN is entered incorrectly three times, the SIM card will be blocked.
If this happens, you can unblock it by using the PUK (Personal Unblocking
Key), which you also may get from your network operator. Please refer to
the topic SIM Card Security documented on page 26 for more detailed
information.
Fixed Wireless Terminal: G30 and G35 models
11
Installation
Note: Once you have entered the PIN code for the first time, you
will not have to enter it again unless you change your SIM card.
The FWT performs this operation automatically in case of power
failure.
Network Search
After you have switched on your FWT and entered the PIN, the FWT
automatically searches for a network.
When a network is found, the Radio LED is on or flashes depending on
the GSM signal strength.
Note: If the Radio LED is off, you do not have access to the GSM
network at your present location.
Now you have prepared the FWT for wall installation. Please, follow the
instructions below for complete wall installation.
Installing the FWT on the Wall
FWT Location
The GSM signal strength available at the FWT location affects the
performance of the unit. The stronger the GSM signal, the better the FWT
performance.
Tip: Test several potential locations by moving the FWT while
looking at the Radio LED. Select the location where the Radio LED
is continuous steady, or the location with the highest amount of
flashes.
Note: Moving the FWT as little as 20 cm can affect the GSM
reception quality.
Location Testing
Number of Radio LED flashes
0 OFF
Location status
Unacceptable
Acceptable
Good
1
2
3
-
-
-
- -
- -
- -
- - -
- - - - - -
Very Good
Excellent
Continuously …………………
Please consider the following recommendations:
12
Fixed Wireless Terminal: G30 and G35 models
Installation
•
Always select an indoor location, preferably close to a window
and as high as possible in the building. Generally, you will
experience better GSM signal strength in these places.
•
•
•
Do not install the FWT in a wet or damp location.
Do not install the FWT in an outdoor location.
Do not install the FWT on walls or in rooms that contain large
amounts of metal, steel or wiring.
•
Do not expose the FWT to extreme temperatures (near
radiators, cooling vents, etc).
If you experience poor reception quality, an outdoor antenna may improve
reception. Please refer to the topic Accessories documented on page 35
for more detailed information,
Wall mounting
Please proceed as indicated in the following picture.
1. Fix the wall-mounting bracket on the wall.
2. Press the FWT against the wall-mounting bracket.
3. Slide the FWT downwards.
Fixed Wireless Terminal: G30 and G35 models
13
Installation
Warning: Once you have fixed the FWT to the wall and switched it
on, check the final status of the LEDs. If either one is off, then there
is a problem with the power supply or the GSM signal.
Now the FWT is ready for connecting devices and making calls.
Note: If you want to remove the FWT from the wall bracket, then
you have to press the tab (step 1) as indicated in the following
picture and then slide the FWT upwards (step 2).
14
Fixed Wireless Terminal: G30 and G35 models
Connecting Devices to the FWT
Connecting Devices to the FWT
Warning: Before you start any connections please refer to the
topic Product Care and Safety documented on page 37 for more
detailed information and contact your network operator if you have
any questions.
Warning: To ensure good protection against electrical discharges
and the best audio quality, proper grounding of the power supply is
strongly recommended.
Connecting devices to the FWT
Connect the devices to the FWT (RJ11 connector) in the same way as
with an analog telephone line. The devices must be connected in parallel.
You can connect the devices directly to the FWT telephone line connector
(RJ11) or make an internal telephone wiring, use RJ11 splitters or similar
connectors.
Fixed Wireless Terminal: G30 and G35 models
15
Connecting Devices to the FWT
Note: When making the connections, the two-wire telephone cable
polarity does not matter.
Tip: If your home or company is already wired with telephone
cable, you only need to connect the cable to the FWT RJ11
connector and your telephone line will be up and running in all
rooms.
Note: The telephone wire must be installed indoors.
Note: The telephone wire should not exceed 600 meters.
Checking the connections
Once the devices (up to 3) have been connected, do the Ring Back Test
as described below in order to check the connections:
•
Lift one telephone and dial **#10#. You will hear a beep tone
and the terminal LEDs will start flashing. Three flashes indicate
it is synchronized.
•
•
Hang up the telephone and check that all the connected
telephones start to ring.
Lift any of the telephones connected and then hang up again.
The ringing will stop and the LEDs will return to normal
operation mode.
Tip: If any of the telephones are not ringing, check your telephone
cable layout and connections to make sure that all devices are
properly connected.
Checking the quality of the calls
Use any of the telephones connected to the FWT terminal to make a call.
Check the speech quality and ask the receiver to call you back to confirm
that you can also receive calls.
If you have problems, please refer to the topic Troubleshooting
documented on page 28 for more detailed information.
Installing the FWT as a telephone line
The FWT is designed to provide a telephone line (RJ11 connector) to
which up to three (3) Fixed Line devices can be connected in parallel. The
FWT provides a single telephone line, which means that only one
communication can take place at a time, in the same way as an ordinary
fixed line.
16
Fixed Wireless Terminal: G30 and G35 models
Connecting Devices to the FWT
Warning: In order to avoid GSM interferences (noise), place the
FWT at least three (3) meters (horizontal) away from electronic
devices, including the telephone equipment connected to the FWT,
or other household electronic devices such as televisions or radio
receivers. The difference in height should be at least 2 meters
(vertical). This is not necessary if you use telephone devices that
fulfill the Immunity Characteristics settled by the IEC CISPR-24
standard. In this case, a minimum security distance of 20 cm is
recommended.
Connecting the FWT to a PBX
This feature is only available for the FWT G35 model. The G35 FWT is
designed to provide a telephone line (RJ11 connector) that behaves in the
same way as an analog trunk.
Generic requirements
The PBX should meet the following generic requirements for FWT
connectivity:
•
•
•
The PBX must provide analog trunks.
One position of the trunk must be assigned to each FWT.
The trunk card must support either Busy Tone Detection (BTD)
or Polarity Reversal Detection on answer and release.
Fixed Wireless Terminal: G30 and G35 models
17
Connecting Devices to the FWT
•
•
The PBX can be programmed to utilize Least Cost Routing
(LCR), if available, to automatically choose the trunk where the
G35 FWT is connected.
If the PBX does not offer LCR, choose the trunk where the FWT
is connected manually with a special dialed prefix. Check the
installation in the same way as before.
The G35 FWT is compatible with most analog PBXs on the market.
G35 FWT connectivity to the analog trunk of the PBX
If the PBX fulfils the requirements for FWT connectivity, listed above,
follow all the installation steps as described in the topic Installing the FWT
on the Wall documented on page 12.
Note: A minimum distance of 3 meters between the G35 FWT and
the PBX is recommended. The cable distance between the PBX
and the G35 FWT should not exceed 600 meters, and the
connection cable should be at least 0.4mm2 in diameter.
Warning: If you install more than one G35 FWT to a PBX, their
antennas have to be separated by 20 cm in height or 2 meters in
the horizontal.
If you are using an analog PBX — disconnect the telephone you have used
to enter the PIN and test the FWT, and connect the analog trunk cable
from the PBX to the FWT telephone line interface.
Check your PBX programming guide to see how to program your PBX to
route certain calls through the FWT trunk if you are using a Least Cost
Routing (LCR) programmed PBX. Once LCR is programmed, make a call
to a mobile telephone number. See if the call is established through the
FWT and check the speech quality.
18
Fixed Wireless Terminal: G30 and G35 models
Connecting Devices to the FWT
If the PBX does not offer the LCR option, choose the FWT trunk manually
with a specific prefix. Check the installation in the same way as before. If
you encounter problems, contact your distributor or network operator.
Warning: The PBX may require specific programming: both
programming and installation should be done by specialized
service personnel.
Using telephones
Telephones connected to the FWT work in the same way as if they were
connected to a fixed line network.
Note: You can also benefit from some GSM functionality that you
usually do not have in the fixed line network. Please refer to the
topic Advanced Features documented on page 20 for more detailed
information.
Please refer to the topic Audible Tones documented on page 31 for more
detailed information.
Fixed Wireless Terminal: G30 and G35 models
19
Advanced Features
Advanced Features
If a DTMF telephone is connected to the FWT, the following features can
be accessed.
Changing Volume
During a call, you can increase or decrease the reception volume level.
•
•
Increase volume: dial R####
Decrease volume: dial R****
Call Divert
You can divert incoming calls to another phone number when you are
unable to answer.
The following table shows the divert alternatives as well as the way to
proceed to manage this function.
Note: These dialing sequences may vary depending on your
network operator. If these do not work, please consult your
network operator or check the user guide provided with your
subscription.
To manage
diversion of calls …
With
Function …
Dial …
You will hear…
Activate
**21*Phone_number#
##21#
1 beep
Deactivate
3 beeps
Always
1 beep if activated
Check status
*#21#
3 beeps if deactivated
Activate
**67*Phone_number#
##67#
1 beep
Deactivate
3 beeps
When busy
1 beep if activated
Check status
*#67#
3 beeps if deactivated
20
Fixed Wireless Terminal: G30 and G35 models
Advanced Features
To manage
diversion of calls …
With
Function …
Dial …
You will hear…
Activate
**61*Phone_number#
##61#
1 beep
Deactivate
3 beeps
When no answer
1 beep if activated
Check status
*#61#
3 beeps if deactivated
Activate
**62*Phone_number#
##62#
1 beep
Deactivate
3 beeps
When out of reach
1 beep if activated
Check status
Deactivate
*#62#
3 beeps if deactivated
All
##002#
3 beeps
Note: If instead of hearing beeps you can hear a deep tone, this
means that there has been an error in the activation or the
deactivation.
Call Restriction / Call Barring
You can restrict certain types of calls that can be made or received. You
need a password to turn a call restriction on or off. Initially, this password
will be 0000.
We recommend you to change it by dialing:
**03**OLD_PASSWORD*NEW_PASSWORD* NEW_PASSWORD#
The following table shows the restriction alternatives as well as the way to
proceed to manage this function.
Note: These dialing sequences may vary depending on your
network operator. If these do not work, please consult your
network operator or check the user guide provided with your
subscription.
To manage restriction
of calls …
With Function …
Dial …
You will hear…
Activate
*33*Password#
#33*Password#
1 beep
Deactivate
3 beeps
All outgoing calls
1 beep if activated
Check status
*#33#
3 beeps if deactivated
Activate
*331*Password#
#331*Password#
1 beep
Deactivate
3 beeps
All outgoing
international calls
1 beep if activated
Check status
*#331#
3 beeps if deactivated
Fixed Wireless Terminal: G30 and G35 models
21
Advanced Features
To manage restriction
of calls …
With Function …
Dial …
You will hear…
Activate
*332*Password#
#332*Password#
1 beep
All outgoing
Deactivate
3 beeps
international calls
except your home
country
1 beep if activated
Check status
*#332#
3 beeps if deactivated
Activate
*35*Password#
#35*Password#
1 beep
Deactivate
3 beeps
All incoming calls
1 beep if activated
Check status
*#35#
3 beeps if deactivated
Activate
*351*Password#
#351*Password#
1 beep
Deactivate
3 beeps
All incoming calls when
you are abroad
1 beep if activated
Check status
Deactivate
*#351#
3 beeps if deactivated
All
#330*Password#
3 beeps
Note: If instead of hearing beeps you hear a deep tone, this means
that there has been an error in the activation or deactivation
Multiparty Calls
You can handle more than one call simultaneously. For example, you can
put an ongoing call on hold, while you make or answer a second call, and
then switch between the two calls.
You can also set up a conference call to have a joint conversation with up
to four people.
Call waiting service
If you wish to be able to receive a second call while another call is in
progress, you must turn on the call waiting service.
Note: These dialing sequences may vary depending on your
network operator. If these do not work, please consult your
network operator or check the user guide provided with your
subscription.
To manage Call waiting
Function…
Dial…
You will hear…
Activate
*43#
#43#
1 beep
Deactivate
3 beeps
1 beep if activated
Check status
*#43#
3 beeps if deactivated
Note: If instead of hearing beeps you hear a deep tone, this means
that there has been an error in the activation or deactivation.
22
Fixed Wireless Terminal: G30 and G35 models
Advanced Features
Making a Second Call
You can only put one call on hold while you make a second call.
•
To hold the active call: press the R key on your telephone and
proceed to make the second call.
•
•
To switch between the two calls, press R2.
To finish the active call and return to the held call, press R1.
Receiving a Second Call
If the call waiting service is on, you hear a tone in the telephone when you
receive a second call.
•
•
To ignore the waiting call, take no action.
To continue with the ongoing call and reject the waiting call
(give a User Busy indication tone to the waiting call): press R0.
•
To end the ongoing call and answer the waiting call: press R1.
Note: If you hang up the telephone, you will also end the ongoing
call and the telephone will ring again so that you can answer the
waiting call as a normal call.
•
To put the ongoing call on hold and answer the waiting call:
press R2. You can switch again between both calls by pressing
R2 each time.
Note: If “divert when busy” is on, the waiting call is diverted to the
number you have specified.
Conference Calls
In a conference call, you can have a joint conversation with up to four
other participants.
To create a conference call
•
If you are in conversation with participant 1, put it on hold
(press R), and dial participant 2.
•
To join the two calls into a conference call: press R3. Now you
have a conference group of three participants (participant 1,
participant 2 and yourself).
To add a new participant (participant 3)
•
Put the conference group on hold (press R) and dial to
participant 3.
•
Join the new participant to the conference group: press R3.
Now you have a conference group of four participants
(participant 1, participant 2, participant 3 and yourself).
Fixed Wireless Terminal: G30 and G35 models
23
Advanced Features
To end the conference call, hang up the telephone. To release a specific
call from the conference group: press R1X (where X is the number of
order of the call).
To choose one call from the multiparty in order to have a private
communication, putting the rest of the conference calls on hold: press
R2X (where X is the number of order of the call you want to communicate
with).
Explicit Call Transfer
To transfer a call to another destination number (B-number).
•
•
Put the ongoing call on hold (press R) and dial the B-number.
Now you can connect this new call, which is ongoing, with the
call you have put on hold, but abandon the conversation
yourself. To do this, press R4.
Phonebook / Abbreviated Dialing
You can store telephone numbers in either the SIM card memory or the
FWT memory. Up to 99 telephone numbers can be stored in each of
them.
The following table shows how to manage the phonebook with the 99
memory positions (Pos).
Warning: The position must always consist of two digits. For
example, memory position number 1 has Pos=01
To manage
the
phonebook in
…
With Function
…
Dial …
You will hear…
Store
**51*Pos*Phone number#
#51*Pos#
1 beep
Delete
3 beeps
SIM card
memory
1 beep if stored
Check position
*#51*Pos*Phone number#
3 beeps if not stored
Dial
Pos#
Dialing …
1 beep
Store
Delete
**51*Pos*Phone number*1#
#51*Pos*1#
3 beeps
Terminal
memory
1 beep if stored
Check position
*#51*Pos*Phone number*1#
3 beeps if not stored
Dial
Pos*
Dialing …
Note: If instead of hearing beeps you hear a deep tone, this means
that there has been an error in the activation or deactivation.
24
Fixed Wireless Terminal: G30 and G35 models
Advanced Features
Voice Mail
The answering service of your network allows callers to leave a voice
message when you cannot answer your calls. If you have voice mail, you
will hear three (3) beeps before the dial tone, as soon as you pick up the
receiver to make a call. Call your voice mail number in order to receive the
voice mail message.
Note: This service may vary depending on your network operator.
If these do not work, please consult your network operator or
check the user guide provided with your subscription.
Sending Tone Signals
During a call, you can press keys 0-9, * and # to perform interactive
services, for example banking by phone or control of an answering
machine.
Minute Minder
If the minute minder is activated, you hear a beep once every minute
during a call as a reminder of the duration of the ongoing call.
To manage minute minder
function…
Dial…
You will hear…
Activate
**42*1#
#42*1#
1 beep
Deactivate
3 beeps
1 beep if activated 3 beeps if
deactivated
Check status
*#42*1#
Note: If instead of hearing beeps you hear a deep tone, this means
that there has been an error in the activation or deactivation.
Alternate Line Service (ALS)
If your SIM card supports the alternate line service, your FWT can handle
two voice lines with different phone numbers, separate bills and perhaps
different subscription services.
With this functionality, you only need one FWT and telephone for both
your personal and work phone numbers, for instance. If necessary, you
may switch from one line to the other.
You will receive all the incoming calls addressed to any of your numbers
independently of the selected line, but your outgoing calls will be charged
to the line you have selected (1 or 2).
Fixed Wireless Terminal: G30 and G35 models
25
Advanced Features
Warning: These dialing sequences may vary depending on your
network operator. If these do not work, please consult your
network operator or check the user guide provided with your
subscription.
To manage alternate line service
function …
Dial …
You will hear…
Activate Line 1
Activate Line 2
**591#
**592#
1 beep
1 beep
1 beep if activated
Check status Line 1
Check status Line 2
*#591#
*#592#
3 beeps if deactivated
1 beep if activated
3 beeps if deactivated
Note: If instead of hearing beeps you hear a deep tone, this means
that there has been an error in the activation or deactivation.
SIM Card Security
To Manage your SIM Card
Most SIM cards are locked at the time of purchase. If the SIM card lock is
on, you have to enter your PIN (Personal Identity Number) the first time
you use your FWT. Please refer to the topic Enter PIN documented on
page 11 for more detailed information.
Note: Once you have entered the PIN code for the first time you
will not have to enter it again unless you change your SIM card.
The FWT performs this operation automatically in case of power
failure.
If you enter your PIN incorrectly three times in a row, the SIM card will be
blocked and the PUK code must be entered to unlock the SIM card.
Please refer to topic To Unblock your SIM Card documented on page 27
for more detailed information.
To Change your PIN
You can change the PIN in the SIM card by dialing from the analog
telephone connected to the FWT with the following sequence:
**04*OLD_PIN*NEW_PIN*NEW_PIN#
Note: If instead of hearing 3 beeps you can hear a deep tone, this
means that there has been an error in the activation or the
deactivation.
26
Fixed Wireless Terminal: G30 and G35 models
Advanced Features
To Unblock your SIM Card
To unblock your SIM card, you need to enter your PUK (Personal
Unblocking Key), which can be supplied by your network operator.
The procedure to enter the PUK is exactly the same as for entering the
PIN.
Note: If you enter the wrong PUK ten times in a row, your card will
be permanently blocked. If this happens, you should contact your
network operator.
In order to unblock your SIM card and change the PIN at the same time,
please dial the following sequence:
**05*PUK*NEW_PIN*NEW_PIN#
Note: If instead of hearing 3 beeps you can hear a deep tone, this
means that there has been an error in the activation or the
deactivation.
Fixed Wireless Terminal: G30 and G35 models
27
Troubleshooting
Troubleshooting
This chapter describes the procedures to identify and, if possible, correct
problems that might occur with the FWT or its installation. Some problems
require that you call your network operator, but most problems you may
encounter can be easily corrected.
LED indicators
The FWT has two LED indicators: The Radio LED (green) indicates the
network signal strength, according to the following table:
Color
OFF
Number of flashes
0
Network signal strength
Unacceptable (no networks)
Acceptable
Green
Green
Green
Green
1 -
-
-
-
2 -- -- --
3 --- --- ---
Good
Very good
Continuous ---------
Excellent
28
Fixed Wireless Terminal: G30 and G35 models
Troubleshooting
The Power LED (red and green) indicates the FWT power supply status:
Color
Green
Red
Power supply situation
Power supply is ON (AC adapter)
The FWT is powered from the battery back-up
Power is OFF
OFF
When both LEDs are flashing simultaneously, it means that the FWT is
under alarm conditions. In this situation, ONLY EMERGENCY CALLS can
be made.
Simultaneous flashing
Alarm status
ENTER PIN
Do this …
Insert the correct PIN. Please refer
to the topic Enter PIN on page11.
ENTER PUK
INSERT SIM
Insert the correct PUK.
Insert the SIM card in the FWT.
SIM failure. Check the SIM or
contact your network operator.
SIM ERROR
1 flash synchronized
Power LED -
Radio LED
-
-
-
-
The FWT is SIM-locked to a specific
network and the inserted SIM card
does not correspond to this
network. Check the SIM or contact
your network operator.
-
WRONG NETWORK
WRONG SUBNETWORK
The FWT is PIN-locked and can only
be used with one SIM card.
Introduce the original SIM or contact
your network operator.
WRONG SIM
FWT LOCKED
The FWT lock function is enabled.
Contact your distributor or network
operator.
2 flashes synchronized
Power LED - - -- --
Radio LED - - - - --
WRONG XXXCK (where
XXX is the name of the
specific password)
The FWT is blocked due to incorrect
password entry. Contact your
distributor or network operator.
3 flashes synchronized
Power LED --- --- ---
Radio LED --- --- ---
Check connections of the FWT or
contact your distributor/ network
operator.
FWT FAILURE
The following table summarizes the different operating status of your FWT
depending on the LEDs, and what to do if a problem is encountered. If
the problem persists, please contact your distributor or network operator.
Fixed Wireless Terminal: G30 and G35 models
29
Troubleshooting
LED indicators status
If you see…
It means…
Do this…
ꢀ
ꢀ
Start using your FWT.
ꢀ
ꢀ
AC power is ON.
If Radio LED is flashing, Please
refer to the topic FWT Location
on page 12.
Power LED Green
The FWT is connected
to the cellular network
and available for use.
Radio LED ON or
flashing
ꢀ
ꢀ
If you are unable to make a
call, check the telephone
cable connection or the PBX
connections and program.
ꢀ
Normal operation mode
Verify that the AC power plug
is securely connected to the
AC power outlet.
ꢀ
ꢀ
Check that the DC power cord
is connected to the FWT.
Both LEDs OFF
ꢀ
AC Power is OFF
Check the circuit breaker or
fuse for the AC electrical circuit
that supplies power to the AC
outlet that the FWT is
connected too.
ꢀ
ꢀ
Verify that the antenna is
properly installed.
ꢀ
ꢀ
AC Power is ON
Verify you have installed the
FWT in the best location and
that the antenna is properly
connected. Please refer to the
topic FWT Location on page
12.
Power LED Green
Radio LED OFF
The FWT is not
connected to the cellular
network. The FWT is not
available for use.
ꢀ
Verify that the AC power cords
are securely connected to the
AC power outlet.
ꢀ
ꢀ
AC power is OFF. The
FWT is operating using
the battery back-up
power
Power LED Red
ꢀ
ꢀ
Check that the power cable is
connected to the FWT.
Radio LED Green
or flashing
The FWT is connected
to the cellular network
and available for use.
Check the circuit breaker or
fuse for the AC electrical circuit
that supplies power to the AC
input of the FWT power supply.
ꢀ
Verify that the AC power cord
is securely connected to the
AC power outlet.
ꢀ
ꢀ
AC power is OFF. The
FWT is operating using
battery back-up power.
ꢀ
ꢀ
Check that the power cable is
connected to the FWT.
Power LED Red
Radio LED OFF
The FWT is not
Check the circuit breaker or
fuse for the AC electrical circuit
that supplies power to the AC
outlet that the FWT is
connected to the cellular
network. The FWT is not
ready for use.
connected to.
ꢀ
ꢀ
Check the alarm status table
above.
ꢀ
ꢀ
Alarm status
Both LEDs Flashing
(simultaneously)
The FWT is blocked or it
has an internal fault
Contact your distributor or
network operator for
assistance.
30
Fixed Wireless Terminal: G30 and G35 models
Troubleshooting
Audible Tones
The FWT generates audible tones in your telephone set, thus providing
the same service characteristics as the one given by the traditional fixed
line network.
The following table describes the nature of the main tones you will get
when using the unit. Other standard call progress tones, such as busy
tone, number obtainable or ring back tone, are provided directly by the
network.
Note: Some tones can vary depending on your network operator.
Tone
1
Name
Dial
Nature
It means...
Regular tone when picking
up the phone
The phone is in service and you
can start your call.
The phone is in service and you
can start your call, but you have
some subscriber service (call
forward, barring or hot line)
activated.
Intermittent long-
cadenced tone when
picking up the phone
2
3
Special dial
Intermittent short-
cadenced tone when
picking up the phone
No service
Howler
No service available.
You have left the handset lifted
for too long without any call in
progress.
4
5
6
Loud and acute tone
Minute
minder
1 beep every minute while
in conversation
It tracks the duration of the call.
When picking up the
phone, three beeps and
then regular tone
You have a voice mail in your
voice mailbox. You need to call
your mailbox to retrieve it.
Voice mail
alert
Subscriber service successfully
activated or positive interrogation
indication.
7
8
9
Positive
Negative
Error
1 beep
3 beeps
Negative interrogation indication.
Subscriber service not activated
or programming procedure not
successfully performed.
1 deep tone
Fixed Wireless Terminal: G30 and G35 models
31
Technical Data
Technical Data
GSM Air Interface
Frequency Bands: GSM 850/1900 or GSM 900/1800.
GSM 850
Frequencies:
RF power:
TX 824-849 MHz, RX 869-915MHz
Maximum 2 W (30 dBm)
Power class 4
GSM 900
Frequencies:
RF power:
TX 880-915 MHz, RX 925-960 MHz
Maximum 2 W (33 dBm)
Power class 4
GSM 1800
Frequencies:
RF power:
TX 1710-1785 MHz, RX 1805-1880 MHz
Maximum 1 W (30 dBm)
Power class 1
GSM 1900
Frequencies:
RF power:
TX 1850-1910 MHz, RX 1930-1990 MHz.
Maximum 1 W (30 dBm)
Power class 1
Speech codec:
Full Rate, Enhanced Full Rate, Half Rate and
Adaptive Multi-Rate (AMR)
32
Fixed Wireless Terminal: G30 and G35 models
Technical Data
FWT Interfaces
Basic Kit
The Basic Kit consists of: FWT unit, power supply, mains cable, wall-
mount bracket, antenna, Quick Installation Guide and User Guide manuals
and telephone cable.
•
•
•
•
Size: Height 148 mm, Width 165 mm
Depth: 45 mm
Weight: 310 grams
SIM card: Small plug-in card, 1.8V or 3V type
Telephone Interfaces
•
•
•
•
•
•
•
•
•
Telephones: RJ11 (a/b 2-wire line); telephone interface
CLI: ETSI DTMF and V.23; Bellcore FSK
Line Impedance: 600 ohm (default)
Loop Current: 25 mA (off-hook)
Open loop voltage: 48 V (on-hook)
Loop resistance: < 650 ohm (off-hook)
Ringing voltage: 45 Vrms
Ring Load: 3 REN; up to 3 telephone devices
Call Control signaling; polarity reversal and loop-break (G35
only)
GSM Antenna
•
•
•
SMA plug-female (50 ohm)
Frequency Bands: GSM 850/1900 or GSM 900/1800
Dual band antennas depending on model types: e.g. model
types FWT G30a / G35a (American) cover the frequencies of
850/1900 MHz and model types FWT G30e / G35e (European)
cover the frequencies of 900/1800 MHz
•
Characteristics: omni directional
Power Supply
•
Power Input VDC: 7.5 VDC; 0.8 A (class 4, male)
Fixed Wireless Terminal: G30 and G35 models
33
Technical Data
•
•
AC Input: 100 - 240 VAC; 47 - 63 Hz 3 pole AC inlet connector
(IEC 320 power inlet)
Available plugs: EU, UK, USA, and AU
Environmental Conditions
•
•
•
•
Operating Temperature: -10ºC to +55ºC
Operating Humidity: 20 — 75 %
Storage Temperature: -40ºC to +85ºC
Storage Humidity: 5 - 95%
34
Fixed Wireless Terminal: G30 and G35 models
Accessories
Accessories
The G3x series FWT benefits from a wide range of accessories, which
ensure the best and easiest way to install, serve and maintain the FWT,
enhancing their functionality. Only these, approved-by-Ericsson,
accessories will guarantee the quality and performance of the FWT.
Antennas
In areas where coverage is poor, the following accessory antenna can be
used to enhance the FWT performance:
External triple band omni directional antenna
External dual band omni directional antenna is used for installation or in
places where indoor coverage is unstable.
Band: dual 900/1800 MHz. Gain: 3dBi. Cable: 3m Connector: SMA male.
Band: dual 850/1900 MHz. Gain: 3dBi. Cable: 3m Connector: SMA male.
Outdoor directional antenna
The directional antenna is intended to be wall or pole mounted by means
of a bracket. The antenna has the highest gain amongst the FWT
antennas. Band: 850/900/1800/1900 MHz. Gains: 10dBi. Cable: 7.5 m.
Connector: SMA male.
Battery
The FWT can be installed with a backup battery:
•
Rechargeable lead-acid battery: 6V, 1.2-1.3 Ah with 2.5 hours
continuous conversation, 13.5 hours stand-by.
Fixed Wireless Terminal: G30 and G35 models
35
Accessories
Warning: Ericsson recommends precaution when handling lead-acid
batteries, and also special attention over storage and power loss
issues. Please refer to the topic Product Care and Safety documented
on page 37 for more detailed information.
Battery Cable
The battery cable is used to connect the backup battery to the FWT.
DC/DC Power Converter
This accessory can be used to connect a DC voltage power system (car
battery, solar cell, etc.) to feed the FWT. DC Input: 10-32 VDC.
Mechanical Antitheft Lock
The mechanical lock serves as an anti-theft device. It fits into the wall
mounting bracket; the FWT is then installed onto the wall mounting
bracket as normal. The mechanical lock prevents removal of the FWT
from the wall mounting bracket. The FWT can be removed by using the
Mechanical Key
Mechanical Antitheft Key
The mechanical key is used to “unlock” the FWT in cases of the
mechanical lock being used. The key is inserted into the “keyhole” at the
bottom of the FWT between the unit and the wall mounting bracket. It
releases the FWT unit from the wall mounting bracket
36
Fixed Wireless Terminal: G30 and G35 models
Product Care and Safety
Product Care and Safety
Note: Please read this information before using your FWT.
Save this User Guide since it contains important safety information and
operating instructions.
Product care
•
Treat your product with care. Keep it in a clean and dust-free
place.
•
•
Do not expose your FWT to liquid or moisture or high humidity.
Do not expose your FWT to extreme high or low temperatures;
refer to the topic Technical Data documented on page 32 for
more detailed information.
•
•
•
Do not expose your FWT to open flames or lit tobacco
products.
Do not use the FWT in an area where a potentially explosive
atmosphere exists.
Do not attempt to disassemble your FWT. A broken warranty
seal will void the warranty. The product does not contain
consumer serviceable components. Only Certified Service
Centers should perform service.
•
Do not use any accessories other than those approved by
Ericsson. Use of non-Ericsson original, or non-Ericsson
approved accessories, may result in loss of performance,
damage to the product, fire, electric shock or injury and may
violate regulations. The warranty does not cover product
failures that have been caused by use of non-Ericsson original,
or non-Ericsson approved accessories.
Fixed Wireless Terminal: G30 and G35 models
37
Product Care and Safety
Antenna care
•
Use only an antenna that has been specifically designed and
approved for your FWT. Use of unauthorized antennas,
modifications, or attachments could damage the FWT and may
violate the appropriate regulations, causing loss of performance
and radio frequency (RF) energy above the recommended
limits.
•
•
•
•
Do not hold or touch the antenna when the FWT is in use.
Holding or touching the antenna affects call quality.
Do not use the FWT if the antenna or antenna cable is
damaged or missing.
Do not place the telephone cord or the power supply cord on
or near the FWT antenna or antenna cable.
Do not cover or place an obstruction on or around the antenna.
Radio wave exposure information
This fixed wireless access terminal is a low-power radio transmitter and
receiver. During use, it emits low levels of radio frequency energy (also
known as radio waves or radio frequency fields).
Governments around the world have adopted comprehensive international
safety guidelines, developed by scientific organizations, e.g. ICNIRP
(International Commission on Non-Ionizing Radiation Protection) and IEEE
(The Institute of Electrical and Electronics Engineers Inc.) through periodic
and thorough evaluation of scientific studies. These guidelines establish
permitted levels of radio wave exposure for the general population. The
levels include a safety margin designed to assure the safety of all persons,
regardless of age and health, and to account for any variations in
measurements.
Specific Absorption Rate (SAR) is the unit of measurement for the amount
of radio frequency energy absorbed by the body. The SAR level for this
product was determined at the highest certified power level in laboratory
conditions using a measurement standard published by the European
Committee for Electrotechnical Standardization (CENELEC).
With the antenna solutions recommended by Ericsson, the maximum
radio wave exposure is below the limit in the international safety guidelines
within a few centimeters from the antenna. Consequently, for
recommended placement of the terminal and antenna, the radio wave
exposure levels are below the limits.
More information on radio frequency exposure can be found on:
38
Fixed Wireless Terminal: G30 and G35 models
Product Care and Safety
Personal medical devices
Radio waves may affect the operation of cardiac pacemakers and other
implanted equipment. If a minimum distance of 15 cm is kept between the
antenna and the pacemaker, the risk of interference is limited. If you have
any reason to suspect that interference is taking place, immediately move
away from the antenna. Contact your cardiologist for more information.
For other medical devices, please consult the manufacturer of the device.
Potentially explosive atmospheres
Do not use your product in an area where a potentially explosive
atmosphere exists.
Power supply
•
Ensure that your AC power outlet is adequately grounded, that
it is situated near the FWT and it is easily accessible.
•
Connect the power supply cord only to the AC power outlet
that meets the specifications marked on the FWT power
supply.
•
Never alter the AC power cord or plug. If necessary have the
correct outlet installed by a qualified electrician or call your
service provider for assistance.
•
•
To reduce risk of damage to the electric cord, remove it from
the outlet by holding onto the AC adapter rather than the cord.
Make sure the cord is positioned so that it will not be stepped
on, tripped over or otherwise subjected to damage or stress.
Children
DO NOT ALLOW CHILDREN TO PLAY WITH YOUR FWT SINCE IT
CONTAINS SMALL PARTS THAT COULD BECOME DETACHED AND
CREATE A CHOKING HAZARD.
Battery information
Warning: When a battery is not installed or is connected to a terminal
that is switched off, it should be recharged during 24 hours every 6
months.
Fixed Wireless Terminal: G30 and G35 models
39
Product Care and Safety
•
Do not expose the battery to extreme temperatures, never
above +60°C. For maximum battery capacity, use the battery in
room temperature.
•
•
Do not let the metal contacts on the battery touch another
metal object. This could short-circuit and damage the battery.
Do not expose the battery to open flames. This could cause the
battery to explode.
•
•
Do not expose the battery to liquid.
Do not allow the battery to be put into the mouth. Battery
electrolytes may be toxic if swallowed.
•
•
Do not puncture or burn the battery. The battery contains
corrosive liquids and materials.
If the battery leaks and the liquid inside spills on the skin or
clothing immediately wash it off with plenty of clean water. If the
liquid splashes into eyes, immediately flush the eyes with plenty
of clean water and consult a doctor.
Moving or Storing the FWT
Turn off the FWT by disconnecting the power supply as well as the battery
(if one is installed).
If you are transporting the FWT on an aircraft, you will be asked to remove
the battery from the unit. For updated information about the transportation
and use of wireless communication equipment, contact the appropriate
local and national regulatory agency or your service provider.
Accessing the battery compartment
This label appears under the battery compartment
indicating that the terminal should always be switched
off before attempting to access the battery
compartment.
40
Fixed Wireless Terminal: G30 and G35 models
Warranty
Warranty
Limited Warranty
Thank you for purchasing this Ericsson Product. To get the maximum use
out of your new product, we recommend that you follow a few simple
steps:
•
•
Read the Guidelines for safe and efficient use.
Read all of the terms and conditions of the Ericsson Warranty
listed below.
•
Save your original receipt, this is necessary for warranty repair
claims. Should your Ericsson Product need warranty service,
you should return it to the dealer from whom it was purchased
or contact your local Ericsson helpdesk for further information.
Ericsson Warranty
Ericsson warrants this Product to be free from defects in material and
workmanship at the time of its original purchase by a customer, and for a
subsequent period of one (1) year.
All accessories for the Product are covered by a warranty period of one (1)
year from the date of original purchase by a customer.
What Ericsson will do
If, during the warranty period, this Product fails to operate under normal
use and service, due to improper materials or workmanship, Ericsson
subsidiaries, authorized distributors, or authorized service partners will
replace the Product in accordance with the terms and conditions
stipulated herein.
For efficiency purposes, Customers are reminded that should their
Ericsson Product need warranty service, they return it to the dealer from
Fixed Wireless Terminal: G30 and G35 models
41
Warranty
which it was purchased or call their local Ericsson helpdesk for further
information on warranty claims.
Conditions
1. The warranty given herein is only valid if the original receipt issued by
the dealer to the original purchaser, specifying the date of purchase
and serial number, is presented along with the Product to be
replaced. Warranty service may be refused if this information is not
available or has been removed or changed after the original purchaser
of the Product from the dealer.
2. Any replaced Product will be warranted for the remainder of the
original warranty period. Replacement may be via functionally
equivalent reconditioned units. Replaced faulty parts or components
will become the property of Ericsson.
3. This warranty does not cover any failure of the Product due to normal
wear and tear, misuse, including but not limited to use in other than a
normal and customary manner, in accordance with Ericsson’s
instructions for use and maintenance of the Product, accident,
modification or adjustment, acts of God, improper ventilation, or
damage resulting from liquid.
4. This warranty does not cover product failures due to repair
installations, modifications or improper service performed by a non-
Ericsson authorized service workshop, opening of the Product by a
non-Ericsson authorized person or use of non-Ericsson original
accessories.
5. Batteries are not covered by this warranty.
6. Tampering with any of the seals on the Product will void this warranty.
7. THERE ARE NO OTHER EXPRESS WARRANTIES, WHETHER
WRITTEN OR ORAL, OTHER THAN THIS PRINTED LIMITED
WARRANTY. ALL IMPLIED WARRANTIES, INCLUDING WITHOUT
LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE
DURATION OF THIS LIMITED WARRANTY. IN NO EVENT WILL
ERICSSON BE LIABLE FOR LOSS OF PROFITS, COMMERCIAL
LOSS, INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY
NATURE; TO THE FULL EXTENT THOSE DAMAGES CAN BE
DISCLAIMED BY LAW.
Some countries do not allow for the exclusion or limitation of loss of
profits, commercial loss, incidental or consequential damages, or
limitation of the duration of implied warranties, so the preceding limitations
or exclusions may not be applicable in certain cases. This warranty gives
specific legal rights, and depending on the country, other rights may be
available as well.
42
Fixed Wireless Terminal: G30 and G35 models
Glossary
Glossary
The following definitions are supplied in order to better understand certain
concepts included in this manual:
B-number
The B-number refers to the number that you dial. It is also commonly
referred to as destination number, called number, called party number.
Fixed Line Devices
Any analog devices that can be connected to the analog fixed line:
•
•
•
Fixed Telephones- ordinary telephones for a fixed line.
G3 Faxes- ordinary fax machines available on the market.
CLI devices- ordinary displays or telephones equipped with
displays that show the caller number for incoming calls.
•
V.90 modems- standard modems for PCs used to make data
connections over the ordinary fixed line.
FWT (Fixed Wireless Terminal)
The FWT is a flexible and cost-effective solution for connecting your
telephone system to the wireless GSM network when there is no fixed
infrastructure or if you need additional telephone lines.
LCR
Least Cost Router: diverts calls to the cheapest package available.
PBX
Private Branch Exchange is a private telephone system that allows
extension to connect to each other as well as the outside world.
PIN
Personal Identity Number. This is the number you get from your network
operator and which you need to access the network. It will prevent the
SIM card to be used by unauthorized people.
PUK
Fixed Wireless Terminal: G30 and G35 models
43
Glossary
Personal Unblocking Key. This is the number you get from your network
operator and which is used to unblock your SIM card if an incorrect PIN
has been entered three times in a row.
SIM
Subscriber Identity Module. SIM card provided by your network operator,
you need to insert in your GSM FWT in order to make and receive calls. It
contains all the information from your subscription characteristic.
Switch-off
Power down the FWT by disconnecting the AC power supply or removing
the battery.
Switch-on
Power up the FWT by connecting the AC power supply or a charged
battery.
Telephone Line
This is the line provided by the FWT (RJ11 connector) that behaves in the
same way as the ordinary fixed line.
Telephone Line Wiring
This is the cable layout that has to be available in order to distribute
telephone lines within a house or office.
44
Fixed Wireless Terminal: G30 and G35 models
Index
Index
Declaration of Conformity, 5
Disposal of the product, 4
A
Abbreviated Dialing, 24
Accessing the battery compartment, 40
Accessories, 35
Advanced Features, 20
Alternate Line Service (ALS), 26
Antenna care, 38
Antennas, 35
Assembly, 9
Audible Tones, 31
E
Enter PIN, 11
Environmental Conditions, 34
Ericsson Warranty, 41
Explicit Call Transfer, 24
External triple band omni directional
antenna, 35
F
B
FCC Statement, 5
Fixed Wireless Terminal, 6
FWT Interfaces, 33
FWT Location, 12
Basic Kit, 33
Battery, 35
Battery Cable, 36
Battery information, 39
G
C
Call Barring, 21
G36 FWT connectivity to the analog trunk of
the PBX, 18
Generic requirements, 17
Glossary, 43
GSM Air Interface, 32
GSM Antenna, 33
Call Divert, 20
Call Restriction, 21
Call waiting service, 22
Changing Volume, 20
Checking the connections, 16
Checking the quality of the calls, 16
Children, 39
I
Installation, 9
Installing the FWT as a telephone line, 16
Installing the FWT on the Wall, 12
Conditions, 42
Conference Calls, 23
Connecting a telephone to the FWT, 10
Connecting devices to the FWT, 15
Connecting Devices to the FWT, 15
Connecting the FWT to a PBX, 17
Copyright, 5
L
LED indicators, 28
Limited Warranty, 41
List of Components, 7
D
DC/DC Power Converter, 36
Fixed Wireless Terminal: G30 and G35 models
45
Glossary
M
S
Making a Second Call, 23
Mechanical Antitheft Key, 36
Mechanical Antitheft Lock, 36
Minute Minder, 25
Moving or Storing the FWT, 40
Multiparty Calls, 22
Sending Tone Signals, 25
SIM Card, 9
SIM Card Security, 27
Supplied Parts, 7
Switch on the FWT, 11
T
Technical Data, 32
N
Network Search, 12
Telephone Interfaces, 33
To Change your PIN, 27
To Manage your SIM Card, 27
To Unblock your SIM Card, 27
Troubleshooting, 11, 16, 28
O
Outdoor directional antenna, 35
P
U
Using telephones, 19
Personal medical devices, 39
Phonebook, 24
Potential explosive atmospheres, 39
Power supply, 39
Power Supply, 33
V
Voice Mail, 25
Preparing Your FWT, 9
Product care, 37
Product Care and Safety, 37
Product Description, 6
W
Wall mounting, 13
Warranty, 5, 41
Welcome, 4
R
Radio wave exposure information, 38
Receiving a Second Call, 23
What Ericsson will do, 41
46
Fixed Wireless Terminal: G30 and G35 models
Ericsson is shaping the future of Mobile and Broadband Internet communications through its
continuous technology leadership. Providing innovative solutions in more than 140 countries,
Ericsson is helping to create the most powerful communication companies in the world.
Ericsson Enterprise AB
All rights reserved.
For questions regarding the product,
Please contact your Ericsson Enterprise Certified Sales Partner.
Also visit us on http://www.ericsson.com/enterprise
© Ericsson AB 2006
EN/LZT 151 233
|