Nortel Networks Switch 50 Series User Manual

BES50_QuickInstallGuide4.pdf  
9/13/2006  
3:12:23 PM  
Busin  
Quick Install Guide  
B
ess  
E
Eth  
S
ern  
5
et Switch 50 Series  
0
17  
192.168.1.255 and then  
click OK.  
Note: By default the  
Read Community is  
“PlsChgMe!RO” and the  
Write Community is  
“PlsChgMe!RW”.  
Steps 11 13  
Powering up  
Steps 4 10  
17. Enter the range  
192.168.1.1 to  
Mounting Options  
Perform steps 11 and  
12 in the order listed.  
!
You can download all documents  
referenced in this Quick Install guide at  
The BES50FE12/24T and BES50GE12/24T switch units can be  
mounted horizontally on a flat surface and stacked with a BCM50.  
11. Insert the power adapter  
into the DC power socket in the  
front of the switch.  
4. If you mount a BES50 unit on a desktop or shelf,  
attach the supplied rubber feet to the bottom of the  
unit. If the BES50 system includes additional units,  
you can set the additional units beside, or stack  
them on top of, the first unit.  
Steps 1 3  
11  
4
Before you  
1
start  
18. Select the BES device from the list of  
network elements on the Element Manager  
tree.  
1. Download the Business Element  
12  
Manager 1.0 Installer to a  
computer on your network.You  
install the Element Manager in  
Step 16.  
18  
19  
5. If you are mounting the additional units  
beside the first unit, attach the supplied  
rubber feet to the bottom of each unit.  
12. Plug the other end  
of the power adapter  
into a grounded, 3-pin  
socket, AC power  
source.  
5
19. Click the Web Page button on the  
Element Manager menu.  
6. If you are stacking the additional units on top of  
the first unit, mount each unit into the tabs on top  
2
6
20. Enter the default username  
of another unit.  
2. Confirm that you have the tools and  
package contents as follows:  
Tools Required:  
(nnadmin) and password  
20  
(PlsChgMe!) to log on to the  
BES50.  
13  
a. Phillips or flathead screwdriver, depending  
on the type of screws used.  
Package contents:  
b. BES50FE-12/24T PWR or  
BES50GE-12/24T PWR switch  
c. Adhesive foot pads (4)  
d. AC power adapter  
C
M
7
13. Check the front-panel LEDs as the device  
powers on to confirm that the PWR LED is green.  
If not, check that the power cable is correctly  
plugged in.  
21  
7. If you mount the switch on a  
desktop or flat surface, attach the  
four adhesive feet to the device as  
indicated.  
Y
21. From the main menu, choose Administration > Quick Start. The  
Quick Start screen appears showing the IP address and other items that  
you can optionally configure. If you want to manually assign IP addresses,  
refer to Using the Nortel Business Ethernet Switch 50 at www.nortel.com.  
CM  
MY  
CY  
CMY  
K
The BES50 series switch performs a short self-test  
as soon as you connect the switch to the power  
supply. The status LED will flash green during the  
self-test, then solid green when finished. If the  
Status LED turns off, the device is not working  
correctly. When the self-test finishes, the BES50  
starts switching data.  
a. Set the device on a flat surface near an AC power source, making  
sure there are at least two inches of space on all sides for proper air flow.  
b. If you install multiple switches, attach four adhesive feet to each one.  
Place each device squarely on top of the one below, in any order.  
BES50-FE/GE-12T PWR switch  
System Indicators  
Port/PoE Status Indicators  
8. To install a BCM50 unit on top of a BES50 unit, place  
the BCM50 unit on top of the BES50.  
RJ-45 Ports with PoE  
8
InSitteipasl14Ac2c1 ess and  
Configuration  
BES50-FE/GE-24T PWR switch  
System Indicators  
Port/PoE Status Indicators  
9. Make sure the feet of the BES50 are in the slots  
on the top of the BCM50 unit and in front of the slots  
9
14  
10. Slide the unit back until it clicks in place on  
RJ-45 Ports with PoE  
RJ-45 Ports  
the slots.  
14. To access the BES50, first install the Business Element  
Manager 1.0. Refer to Element Manager documentation at  
10  
3. Check your cables; when you install  
the switch into a network make sure you  
use the following required cables:  
3
15. Start the Element Manager.  
• Category 3 UTP or STP cables with an RJ-45 connector  
(for 10BASE-T ports).  
You are now ready to use the BES50 series switch in  
your network installation.  
15  
Slots  
Feet  
• Category 5 UTP or STP cables with an RJ-45 connector  
(for 100BASE-TX ports).  
• Category 5, 5e, or 6 UTP or STP cables with an RJ-45  
connector (for 1000BASE-T ports).  
16. From the Element Manager  
Refer to Using the Nortel Business Ethernet Switch 50  
instructions.When you connect a PC directly to the  
BES50, use the default IP address 192.168.1.128  
menu, choose Network > Find  
16  
Network Elements > Business  
Ethernet Switch.  
N0128198  
 

NEC Personal Computer PD75P308 User Manual
Nokia Satellite TV System 9400 S User Manual
Nortel Networks Switch 325 series User Manual
Novatel TV Antenna 42GOXX16A4 XT 1 1 User Manual
Palsonic TV DVD Combo 3415DVD User Manual
Panasonic All in One Printer KX F880 User Manual
Panasonic Answering Machine KX T5000 User Manual
Panasonic Laptop Docking Station CF VEB342 User Manual
Panasonic Switch 2SD1824 User Manual
Patton electronic Network Router 3040 V35 User Manual