Nortel Networks Cordless Telephone T7316E User Manual

A
Return  
to Menu  
Wall mount with a telephone stand  
1
Cord connections  
1
B
J
J
Press here to remove the stand.  
C
H
I
T7316E Telephone User Card  
D
key hole slots  
Use the key hole slots on the stand  
to mark the location for the screws.  
Tighten screws for a secure fit.  
Slide feature card plate down.  
K
K
E
2
Desk mount option  
Route line cord through the stand.  
2
L
F
G
Headset option  
Connect cord to  
headset.  
Mount the stand as shown.  
Connect cords to the telephone,  
refer to Cord connections”  
illustrations.  
Connect cord  
to handset.  
3
1-800-4 NORTEL  
M
N
© 2003 Nortel Networks  
P0603479 02  
Mount the telephone  
onto the screws and  
slide it down.  
3
Printed in Canada  
Connect line cord  
to wall jack.  
Connect line cord to  
wall jack.  
Your T7316E telephone  
More on your T7316E telephone  
A
Telephone light  
G
Audio cluster buttons  
Flashes for incoming calls.  
Wall mount without a telephone stand  
1
Telephone setup  
© Mute button  
Turns the microphone off or on when you are on a call.  
Handsfree button  
For more information on using the handsfree feature,  
refer to the “Handsfree calls” section in this card.  
¬ Headset button  
Lights up when Message Waiting Indication (MWI) is  
supported by system software. Contact your system  
administrator for more information.  
Display contrast level  
Press here to remove the stand.  
Adjust the contrast of your display.  
1. Press ≤•‡.  
B
C
Adjustable tilt display  
Connect cords to the telephone,  
refer to Cord connections”  
illustrations.  
2. Press UP or DOWN to view the levels.  
3. Press OK to select a level.  
Shows the time and date, call and feature information.  
Turns the headset mode on.  
Display buttons  
H
I
Feature button  
The label for display buttons appear in capital letters  
on the bottom of the display. Display buttons change  
with each feature you use.  
Language choice  
Starts or ends a feature.  
≤•fi‚⁄  
Hold button  
2
Select Primary Language for the telephone display.  
≤•fi‚¤  
Places calls on hold.  
Contrast level 2  
Feature message  
Select Alternate Language for the telephone display.  
≤•fi‚‹  
J
K
L
Memory buttons  
DOWN UP OK  
Display button label  
Select Alternate Language 2 for the telephone display.  
≤•fi‚›  
Memory and line buttons  
Display button  
Indicators  
D
® Release button  
Select Alternate Language 3 for the telephone display.  
Appear next to active line and memory buttons.  
Ends an active call or feature.  
Ring type  
M
N
Number card  
E
F
Dial pad  
Select a different ring for your telephone.  
1. Press ≤•fl.  
Connect line cord to  
wall jack.  
Write your extension number on this card.  
Volume control  
Adjusts the handset, handsfree, headset and ringer  
volume.  
2. Press , ¤, , or NEXT to hear the different  
ring types.  
3. Press OK to store the ring type.  
Feature card plate  
Place the telephone onto  
the wall mount plate and  
slide it down.  
Storage compartment for your feature card.  
 

Moxa Technologies Switch UC 7408 User Manual
Multiquip Portable Generator EGC500DD User Manual
Multiquip Septic System ST 3050D User Manual
Murray Lawn Mower MB12538LT User Manual
Musical Fidelity CD Player M1CDT User Manual
National Instruments Network Card IMAQ Vision for Measurement Studio User Manual
Network Technologies Switch 900GV User Manual
Olympus Camcorder E M5 User Manual
Optimus Cassette Player SCP 87 User Manual
Panasonic Network Card BL PA300A User Manual