Nortel Networks Answering Machine P0908524 User Manual

Enterprise Edge Voice Messaging  
Reference Guide  
1-800-4 NORTEL  
www.nortelnetworks.com  
© 1999 Nortel Networks  
P0908524 Issue 01  
 
4 Contents  
Assigning message delivery options using the Open Mailbox feature  
45  
Assigning message delivery options using the Leave Message feature  
46  
Enterprise Edge Voice Messaging Reference Guide  
P0908524 Issue 01  
 
Contents 5  
Transferring a mailbox owner’s call to Enterprise Edge Voice  
Messaging 56  
Programming an Outbound Transfer telephone number when Enterprise  
Edge Voice Messaging is behind PBX or Centrex+ 60  
Changing the destination type from a pager to a telephone or extension  
74  
Setting up Off-premise Message Notification to more than one destination  
P0908524 Issue 01  
Enterprise Edge Voice Messaging Reference Guide  
 
How to use this guide  
1
Introduction  
Use the Enterprise Edge Voice Messaging Reference Guide with the Enterprise  
Edge Voice Messaging Quick Reference Guide. The Enterprise Edge Voice  
Messaging Reference Guide gives you detailed information about using the  
Enterprise Edge Voice Messaging system.  
This chapter describes:  
How the Enterprise Edge Voice Messaging Reference Guide is  
organized  
The Enterprise Edge Voice Messaging Reference Guide contains the following  
chapters:  
Chapter  
Description  
Describes the contents and conventions of this guide.  
Describes Enterprise Edge telephones, how Alternate sets  
work, Enterprise Edge ATA 2, entering characters on the  
Enterprise Edge dialpad, Enterprise Edge Voice  
Messaging voice prompts, the Automated Attendant,  
types of mailboxes and exiting Enterprise Edge Voice  
Messaging.  
Shows how to initialize and open your mailbox. Explains  
passwords, the Company Directory and Assigning a  
Target Attendant.  
Describes feature codes and mailbox options.  
Describes Primary, Alternate, Personalized and  
Information mailbox greetings. Shows how to record and  
choose greetings.  
Describes Receiving Calls, the Enterprise Edge Voice  
Messaging Never Full mailbox feature, listening to your  
mailbox messages, and Call Screening.  
Explains types of messages, using the Company  
Directory, message delivery options, recording and  
sending a message, replying to messages and how to send  
a message to more than one recipient.  
Describes Call Forwarding your calls.  
Describes transferring calls and Outbound Transfer.  
P0908524 Issue 01  
Enterprise Edge Voice Messaging Reference Guide  
 
           
8 How to use this guide  
Chapter  
Description  
Explains what Off-premise Message Notification is and  
shows how to set up and change Off-premise Message  
Notification.  
Describes the Call Record feature.  
Provides suggestions for the optimal use of Enterprise  
Edge Voice Messaging.  
Provides helpful procedures for problems that might  
occur while operating Enterprise Edge Voice Messaging.  
Provides a list of default values and tone commands.  
Index  
Defines terms used in this guide.  
Provides an alphabetical list of information contained in  
this guide.  
Conventions and symbols used in this guide  
The following conventions and symbols are used for describing features and their  
operation:  
Convention  
Example  
Used for  
Word is in a special font (shows  
top line of display)  
Pswd:  
Command line prompts. Used on Enterprise Edge  
one line and two line display telephones.  
Underlined word in capital letters PLAY  
(shows bottom line of a two-line  
display telephone)  
Display button option. Available only on Enterprise  
Edge two line display telephones. You can press the  
button directly below the option on the display to  
proceed.  
Dialpad buttons  
£
Represents the buttons you press on the dialpad to  
select a particular option.  
Prerequisites  
If you are a new user, make sure you are familiar with how to operate Enterprise  
Edge single-line and two-line display telephones. Refer to Enterprise Edge  
telephones on page 9 and read the Enterprise Edge Telephone User Card that came  
with your telephone.  
For more information about Enterprise Edge Voice Messaging, ask your System  
Administrator.  
Enterprise Edge Voice Messaging Reference Guide  
P0908524 Issue 01  
 
       
Using Enterprise Edge Voice Messaging  
2
Introduction  
Enterprise Edge Voice Messaging works with the Enterprise Edge system to  
provide an automated receptionist service. Enterprise Edge Voice Messaging  
answers incoming calls, routes them to extensions and mailboxes in the system, and  
provides message taking capability.  
This chapter describes:  
Enterprise Edge telephones  
Enterprise Edge one line display telephones  
You can use Enterprise Edge one line display telephones for most Enterprise Edge  
Voice Messaging sessions. If you are a using an Enterprise Edge one line display  
telephone, the display shows the Enterprise Edge Voice Messaging display  
command line. The Enterprise Edge one line display telephone does not show the  
display button options.  
On an Enterprise Edge one line display telephone, all options are given immediately  
by the voice prompts. You make selections using the dialpad only. You do not need  
to wait for the voice prompt to complete the option list. You can interrupt the voice  
prompt and make your selection immediately.  
P0908524 Issue 01  
Enterprise Edge Voice Messaging Reference Guide  
 
                 
1 0 Using Enterprise Edge Voice Messaging  
Enterprise Edge two line display telephones  
Enterprise Edge two line display telephones show you Enterprise Edge Voice  
Messaging commands and options. All system administration tasks, such as setting  
up a Group List, require a two-line display telephone.  
Enterprise Edge two line displays can show up to three display button options at a  
time. In cases where there are more options, wait for the voice prompt to state the  
other available options. If you know the corresponding dialpad number for the  
option you want, you can press it any time during the voice prompt.  
Press to return to the previous display prompt.  
An example of the Enterprise Edge Voice Messaging two-line display is shown in  
Enterprise Edge two line display  
Display command line  
Display button options  
Pswd:  
OTHR  
RETRY  
OK  
Display buttons  
Alternate extensions  
You can have up to two Alternate extensions for your mailbox. If a caller dials the  
main extension (an extension that has Alternate extensions assigned), the call rings  
only at the main extension.  
If the call is not answered and a message is left, a message indicator appears at the  
main extension and at the Alternate extension(s). You can access the message from  
the Alternate extension(s) with ƒ·°⁄, the same way that you usually  
access messages from your main extension telephone.  
If an Alternate extension is assigned to a telephone that has Caller ID (CLID) and  
Display Caller enabled, CLID information displays and an audible tone occurs at all  
telephones when the call goes to Enterprise Edge Voice Messaging. (For  
information on enabling Display Caller refer to Call Forward with Caller ID (CLID)  
on page 52.) The message can be intercepted using the Interrupt Feature,  
ƒ·°‡, at all telephones as long as the caller is still leaving a  
message.  
Enterprise Edge Voice Messaging Reference Guide  
P0908524 Issue 01  
 
           
Using Enterprise Edge Voice Messaging 1 1  
Enterprise Edge ATA 2  
You can use a single-line Enterprise Edge telephone for most Enterprise Edge  
Voice Messaging sessions. However, you cannot use a single-line telephone  
attached to an Enterprise Edge ATA 2 for Enterprise Edge Voice Messaging  
System Administration tasks.  
There is no Message Waiting Notification when you are using an Enterprise Edge  
ATA 2.  
Although a single-line telephone does not have a feature button, you can access  
Enterprise Edge Voice Messaging features.  
To access Enterprise Edge Voice Messaging features, such as the Leave Message  
feature or the Open mailbox feature, call Enterprise Edge Voice Messaging and  
follow the voice prompts. You can determine the Enterprise Edge Voice Messaging  
extension by pressing ƒ·°fi on an Enterprise Edge telephone.  
You can also press:  
˚•·°⁄ to open your mailbox  
or  
˚•·°‚ to leave a message, and follow the voice prompts.  
Entering characters on the Enterprise Edge dialpad  
The buttons on your Enterprise Edge telephone dialpad act as both numbers and  
letters. Each button represents a number and also represents letters of the alphabet.  
You can enter a maximum number of 16 characters on the command line of the  
Enterprise Edge dialpad. The display shows 16 characters at a time. The prompt  
remains on the display if you enter fewer than ten characters.  
If you are entering information where the prompt and the information is fewer than  
16 characters, you can see both the prompt and the information you entered.  
An example of a display with fewer than 16 characters, where the command line  
prompt remains on the display is the Pswd command line prompt.  
Pswd:1111  
OTHR RETRY OK  
The prompt disappears for the following command line prompts:  
Name:  
Log:  
Dest ph:  
P0908524 Issue 01  
Enterprise Edge Voice Messaging Reference Guide  
 
                     
1 2 Using Enterprise Edge Voice Messaging  
For instance, the following display shows the Name: command line prompt:  
Name:  
RETRY  
BKSP  
OK  
When you begin to enter the last name, the Name: command line prompt disappears.  
For example, if you are entering the name Partridge, you press the dialpad button  
for P, and the display drops the Name: prompt.  
P
RETRY  
BKSP  
OK  
The command line prompt is still not shown on the display after you enter the entire  
name, although the name is only nine characters.  
PARTRIDGE  
RETRY  
BKSP  
OK  
Enterprise Edge Voice Messaging voice prompts  
All Enterprise Edge telephones provide voice prompts.  
The voice prompt tells you the dialpad button to press to use different Enterprise  
Edge Voice Messaging options. Voice prompts provide the same options as display  
buttons. Prompts also provide options that do not appear on the display. If you are  
using an Enterprise Edge two line display telephone, you can use either the display  
button or the dialpad button to access the option.  
On an Enterprise Edge one line display telephone the voice prompt plays  
immediately. If you do not choose an option after five seconds, the voice prompt  
replays the options. If you still do not choose an option, Enterprise Edge Voice  
Messaging ends the session.  
On an Enterprise Edge two line display telephone the voice prompt plays after a  
five-second delay. If you do not choose an option, Enterprise Edge Voice  
Messaging ends the session.  
Interrupting a voice prompt  
You can interrupt a voice prompt by selecting any option on the display or dialpad.  
You can also interrupt a voice prompt by pressing £. You cannot interrupt a voice  
prompt that is informing you of an error.  
Enterprise Edge Voice Messaging Reference Guide  
P0908524 Issue 01  
 
         
Using Enterprise Edge Voice Messaging 1 3  
Automated Attendant  
The Automated Attendant acts as a receptionist for incoming calls. When enabled,  
the Automated Attendant answers your company’s incoming telephone lines  
depending on the time of day. If callers know which option they want, they can  
interrupt the Automated Attendant by entering their selection on the dialpad of any  
tone-dial telephone.  
The Automated Attendant provides callers with voice prompt commands associated  
with each of the following options:  
entering a mailbox number  
entering the extension  
using the Company Directory  
leaving a message  
reaching the Operator  
selecting an Alternate Language* (not a voice prompt)  
* If your Enterprise Edge Voice Messaging system is installed with bilingual  
capabilities, the caller can press · to listen to the Automated Attendant in the  
Alternate Language.  
When a caller selects an option, the Automated Attendant responds to the command  
either by routing the call to an extension or mailbox within your company, or  
directing the caller to the Company Directory or the Operator.  
The caller listens and then enters the option they want to use.  
Types of mailboxes  
A mailbox is a storage place for messages. A Enterprise Edge Voice Messaging  
system can have up to 1,000 mailboxes. There are three types of mailboxes:  
Personal  
Information  
Special  
Most users have personal mailboxes.  
Personal mailbox  
A personal mailbox is assigned by the System Administrator and is maintained by  
the mailbox owner. A personal mailbox can be a user or a guest mailbox.  
User mailbox  
A user mailbox can be assigned to each mailbox owner who has an operating  
Enterprise Edge extension.  
P0908524 Issue 01  
Enterprise Edge Voice Messaging Reference Guide  
 
                 
1 4 Using Enterprise Edge Voice Messaging  
Guest mailbox  
Guest mailboxes provide temporary employees and guests with access to internal  
messaging and call routing features. Guest mailboxes do not have an operating  
extension. They are assigned a number that looks and works like an extension. This  
allows the guest mailbox owner to access Enterprise Edge Voice Messaging the  
same way a mailbox owner accesses their mailbox from another extension or  
telephone. If you need a guest mailbox, request one from the System Administrator.  
Information mailbox  
An Information mailbox is designed to provide an informative message to a caller.  
These mailboxes do not have an operating Enterprise Edge extension, and the caller  
cannot leave a message in them. A voice prompt provides a caller with access to  
Information mailboxes. An Information mailbox is reached through the Automated  
Attendant, Custom Call Routing (CCR) or the Operator. For more information,  
Information mailboxes are created by the System Administrator, and are maintained  
by either the System Administrator or a mailbox owner.  
Special mailboxes  
Special mailboxes are set up automatically when the Enterprise Edge Voice  
Messaging system is initialized.  
The Special mailboxes include:  
General Delivery mailbox  
System Administrator mailbox  
General Delivery mailbox  
The General Delivery mailbox is used:  
to collect messages from callers who use a rotary dial telephone  
for individuals in your company who do not have personal mailboxes  
for mailbox owners whose mailboxes are full. For more information, refer to the  
The receptionist or System Administrator sends messages left in the General  
Delivery mailbox to the appropriate mailbox owner. For more information about  
the General Delivery mailbox, refer to Default mailbox numbers for the General  
System Administrator mailbox  
This mailbox is used by your System Administrator as a personal mailbox. You can  
leave messages for your company’s System Administrator in this mailbox.  
Ask your System Administrator for the mailbox number.  
Enterprise Edge Voice Messaging Reference Guide  
P0908524 Issue 01  
 
               
Setting up your mailbox  
3
Introduction  
This chapter shows you how to set up your mailbox and describes the following  
topics:  
Initializing your mailbox  
Initializing your mailbox prepares your mailbox to receive messages. Your mailbox  
cannot receive and store messages until it is initialized.  
Initializing your mailbox involves:  
choosing a password from four to eight digits long that does not start with zero  
changing the Enterprise Edge Voice Messaging default password to your new  
password  
recording your name in the Company Directory (refer to Recording or changing  
To initialize your mailbox, follow the steps in Initializing and opening your mailbox  
P0908524 Issue 01  
Enterprise Edge Voice Messaging Reference Guide  
 
             
1 6 Setting up your mailbox  
Initializing and opening your mailbox for the first time  
To initialize and open your mailbox for the first time:  
1. Press ƒ·°⁄.  
2. Press ‚‚‚‚ (the default password) and press  
Pswd:  
OTHR  
RETRY  
OK  
OK or £.  
Note: If you are at another Enterprise Edge set, press  
OTHR or to access the Log: display prompt.  
From the Log: prompt, enter your mailbox  
number and password as a continuous number.  
Your mailbox number is normally the same as  
your extension. Your default password is  
‚‚‚‚.  
3. This display appears briefly to indicate that you must  
change your password.  
Must change pswd  
4. Choose a password from four to eight digits long that  
does not start with zero. Enter your new mailbox  
password and press OK or £.  
Pswd:  
RETRY  
OK  
5. Enter your new mailbox password again and press OK  
Again:  
RETRY  
OK  
OK  
or £.  
6. At the tone, record your name in the Company  
Directory. Press OK to end your name. Press RETRY or  
¤ to erase and re-record your name.  
Record name:  
RETRY  
Note: Include your mailbox number in your  
Company Directory recording. For example  
Paul Wayne, mailbox 5813”.  
7. Press OK or £ to accept the recording. Press PLAY or  
to listen to the recording. Press RETRY or ¤ to  
erase and re-record your name.  
Accept name?  
RETRY  
PLAY  
OK  
8. Press ® to end the session.  
0 new 0 saved  
PLAY REC  
ADMIN  
After your mailbox is initialized, record your Personal mailbox greetings. If you do  
not record any Personal greetings, your Company Directory name recording plays  
to callers who reach your mailbox.  
Enterprise Edge Voice Messaging Reference Guide  
P0908524 Issue 01  
 
   
Setting up your mailbox 1 7  
Opening your mailbox  
You can open your mailbox from:  
your own extension  
another Enterprise Edge Voice Messaging extension  
an outside telephone (as shown in Opening your mailbox remotely)  
Opening a mailbox after it is initialized  
This section describes how to open:  
your mailbox from your own telephone  
your mailbox from another Enterprise Edge extension  
a Guest mailbox  
After a mailbox is initialized, follow these steps to open it:  
1. Press ƒ·°⁄.  
2. Enter your mailbox password and press OK or £.  
Pswd:  
OTHR  
RETRY  
OK  
Note: If you are at another Enterprise Edge  
extension, or if you are using a Guest mailbox,  
press OTHR or to access the Log: display  
prompt. From the Log: prompt, enter your  
mailbox number and password as a continuous  
number. Your mailbox number is normally the  
same as your extension.  
Opening your mailbox remotely  
If you are calling your Enterprise Edge Voice Messaging mailbox from an outside  
telephone, press •• during your greeting to open your mailbox. At the voice  
prompt, enter your mailbox number, password and press £. Follow the voice  
prompts.  
P0908524 Issue 01  
Enterprise Edge Voice Messaging Reference Guide  
 
           
1 8 Setting up your mailbox  
Mailbox Password  
Your password is from four to eight digits long and cannot start with zero. When  
you initialize Enterprise Edge Voice Messaging, the default mailbox password is  
four zeros (0000). You are prompted to change this password.  
It is recommended that you change your password every 30 days. By changing your  
password regularly, you decrease the chance that someone will discover your  
password and gain access to your system.  
Keep a written copy of your password in a safe place, and avoid giving it to your  
co-workers. Your mailbox password is used to keep your voice messages private  
and confidential. For security reasons, it is a good idea to choose an uncommon  
password (not a predictable password like 1234 or 1111). If someone else knows  
your password, they can access your mailbox and listen to or delete your messages.  
They can also access your Enterprise Edge Voice Messaging system and use it  
fraudulently or disrupt service.  
Changing your mailbox password  
You can change your mailbox password at any time. Remember to choose a  
password from four to eight digits long that does not start with zero.  
To change your password:  
1. Press ƒ·°⁄ to open your mailbox.  
2. Enter your mailbox password and press OK or £.  
Pswd:  
OTHR  
RETRY  
OK  
3. Press ADMIN or °.  
0 new 0 saved  
PLAY REC  
ADMIN  
4. Press PSWD or .  
Mailbox admin  
GREET PSWD QUIT  
5. Enter your new mailbox password and press OK or £.  
Pswd:  
RETRY  
OK  
OK  
6. Enter your new mailbox password again and press OK  
Again:  
RETRY  
or £.  
7. Press ® to end the session.  
Mailbox admin  
GREET PSWD QUIT  
Enterprise Edge Voice Messaging Reference Guide  
P0908524 Issue 01  
 
           
Setting up your mailbox 1 9  
Company Directory  
The Company Directory is a list of mailbox owners on the Enterprise Edge Voice  
Messaging system. Before your mailbox can be used to receive messages, you must  
record your name in the Company Directory. It is a good idea to include your  
mailbox number in your Company Directory recording. For example “Paul Wayne,  
mailbox 5813”.  
This establishes your “voice” name in a directory that is used by other Enterprise  
Edge Voice Messaging users and outside callers who use the Company Directory.  
If you do not want your name in the Company Directory, ask your System  
Administrator. The Company Directory feature can be disabled by the System  
Administrator. If you are unsure whether or not you have this feature, ask your  
System Administrator.  
Recording or changing your name in the Company Directory  
Names included in the Company Directory can be changed at any time.  
To change your name in the Company Directory:  
1. Press ƒ·°⁄ to open your mailbox.  
2. Enter your mailbox password and press OK or £.  
Pswd:  
OTHR  
RETRY  
OK  
3. Press ADMIN or °.  
0 new 0 saved  
PLAY REC  
ADMIN  
4. Press .  
Mailbox admin  
GREET PSWD QUIT  
Note: This is a voice prompt option. It does not  
appear as a display button option on a two-line  
display telephone.  
5. At the tone, record your name. Press OK or £ to end  
your recording. The recording of your name is  
automatically placed in the Company Directory.  
Record name:  
RETRY  
OK  
OK  
6. Press OK or £ to accept your recording. Press PLAY  
or to listen to the recording. Press RETRY or ¤ to  
erase and re-record your name in the Company  
Directory.  
Accept name?  
RETRY  
PLAY  
7. Press ® to end the session.  
Mailbox admin  
GREET PSWD QUIT  
P0908524 Issue 01  
Enterprise Edge Voice Messaging Reference Guide  
 
         
2 0 Setting up your mailbox  
Assigning a Target Attendant  
The person that you assign to answer your telephone is your Target Attendant.  
After you assign your Target Attendant, a caller who reaches your mailbox can  
press to speak with the Target Attendant. If the Target Attendant does not  
answer, the call goes to your mailbox. If your personal mailbox is not available, the  
call goes to the General Delivery mailbox.  
Remember to tell callers in your greetings that if they need assistance they can press  
to speak to Target Attendant. For example, “Please press to speak to my  
assistant.” The Target Attendant can be any valid extension. The default Target  
Attendant is the person assigned as the Enterprise Edge Voice Messaging Operator.  
To assign your personal Target Attendant:  
1. Press ƒ·°⁄ to open your mailbox.  
2. Enter your mailbox password and press OK or £.  
Pswd:  
OTHR  
RETRY  
OK  
3. Press ADMIN or °.  
0 new 0 saved  
PLAY REC  
ADMIN  
4. Press .  
Mailbox admin  
GREET PSWD QUIT  
5. Press CHNG or to change the Target Attendant. The  
Atdt ext:oper prompt indicates that the current  
Target Attendant is the Enterprise Edge Voice  
Messaging Operator.  
Atdt ext: oper  
CHNG  
QUIT  
OPER  
QUIT  
6. Enter the extension number of your new Target  
Attendant. Press OPER or to change the Target  
Attendant back to the Enterprise Edge Voice  
Messaging Operator.  
Ext:  
RETRY  
7. The Atdt ext:xxx prompt appears, where xxx  
represents the extension you entered. Press QUIT to  
accept the number of the Target Attendant. Press CHNG  
or to change the Target Attendant.  
Atdt ext: <xxx>  
CHNG  
Press ® to end the session.  
Enterprise Edge Voice Messaging Reference Guide  
P0908524 Issue 01  
 
       
Feature codes and mailbox options  
4
Introduction  
This chapter describes the Enterprise Edge Voice Messaging feature codes and  
mailbox options, and includes the following topics:  
Feature codes  
Enterprise Edge Voice Messaging feature code.  
Feature codes are assigned during installation. The feature codes in this guide are  
the default feature codes. If your company is using custom feature codes, you need  
to find out what the custom feature codes are. To determine the Enterprise Edge  
Voice Messaging custom feature codes, refer to Determining custom feature codes  
Once you know the feature codes that your company is using (default feature codes  
or custom feature codes), you can program the feature codes onto memory buttons.  
P0908524 Issue 01  
Enterprise Edge Voice Messaging Reference Guide  
 
           
2 2 Feature codes and mailbox options  
Feature Code Name  
Default feature code  
Description  
Leave Message  
ƒ·°‚  
Leaves a message in a mailbox. No password  
is required.  
Open Mailbox  
Operator Status  
ƒ·°⁄  
Opens your Personal mailbox to listen to your  
messages and access Enterprise Edge Voice  
Messaging options. Your personal password  
is required.  
ƒ·°¤  
Not a user feature. Used by the System  
Administrator, receptionist, or Operator to set  
the Operator Status.  
Call Forward to  
Enterprise Edge Voice  
Messaging  
ƒ·°›  
Forwards incoming calls to Enterprise Edge  
Voice Messaging.  
Enterprise Edge Voice ƒ·°fi  
Messaging extension  
Determines the Enterprise Edge Voice  
Messagingextension. You need to know what  
the Enterprise Edge Voice  
Messagingextension is when you forward  
your extension to Enterprise Edge Voice  
Messaging.  
Transfer  
Interrupt  
ƒ·°fl  
Transfers calls to a mailbox.  
ƒ·°‡  
Interrupts Enterprise Edge Voice Messaging  
when a caller is listening to your personal  
mailbox greeting or leaving a message. This  
allows you to speak with a caller who has  
reached your mailbox. (Refer to the Note that  
follows this table.)  
Call Record  
ƒ·°·  
Records a telephone call from your  
Enterprise Edge telephone. The resulting  
message is left in your mailbox.  
Note: When a caller leaving a message in a mailbox is interrupted, the part of the  
message that is recorded before the interruption remains in the mailbox.  
Delete this message. If Off-premise Message Notification is turned on, the  
interrupted message causes Enterprise Edge Voice Messaging to call the  
Off-premise Message Notification number immediately. For information on  
Off-premise Message Notification, refer to About Off-premise Message  
If Outbound Transfer is turned on, you cannot interrupt the call unless you  
interrupt it before the caller transfers to your Outbound Transfer destination  
number by pressing . For information on Outbound Transfer, refer to  
Enterprise Edge Voice Messaging Reference Guide  
P0908524 Issue 01  
 
   
Feature codes and mailbox options 2 3  
Determining custom feature codes  
If your company is using custom feature codes, find out what the custom feature  
codes are. To determine the Enterprise Edge Voice Messaging custom feature  
codes, use an Enterprise Edge two line display telephone.  
To determine the Enterprise Edge Voice Messaging feature codes:  
1. Press ƒ·•⁄.  
Leave msg: F9xx  
NEXT  
2. The name and numerical code of the first feature, the  
Leave Message feature, is shown on the display. The  
xx represents a number between 00 and 99. Record the  
custom feature code for the Leave Message feature in  
the appropriate column in the table Description of  
Open mbox: F9xx  
NEXT  
3. The display shows the name and numerical code of the  
Open Mailbox feature. Record the feature code for the  
Open Mailbox feature in the appropriate column in the  
NEXT.  
4. Continue pressing NEXT to show all of the Enterprise  
Edge Voice Messaging feature codes and record them  
in the appropriate column in the table Description of  
Interrupt: F9xx  
QUIT  
5. This display is shown when you reach the last  
Enterprise Edge Voice Messaging feature code, the  
Interrupt feature code. Press QUIT or ® to end the  
session.  
After you have determined the custom feature codes, make sure that you record the  
custom feature codes in the appropriate column.  
Table 1 Description of feature codes  
Feature Code name  
Leave Message  
Open Mailbox  
Default feature code  
Custom feature code  
ƒ·°‚ ƒ· ___ ___  
ƒ·°⁄ ƒ· ___ ___  
ƒ·°¤ ƒ· ___ ___  
ƒ·°› ƒ· ___ ___  
Operator Status  
Call Forward to Enterprise Edge Voice  
Messaging  
Transfer  
ƒ·°fl ƒ· ___ ___  
ƒ·°‡ ƒ· ___ ___  
ƒ·°· ƒ· ___ ___  
Interrupt  
Record Call  
P0908524 Issue 01  
Enterprise Edge Voice Messaging Reference Guide  
 
       
2 4 Feature codes and mailbox options  
Programming a memory button with a feature code  
Each Enterprise Edge Voice Messaging feature code can be programmed to a single  
memory button.  
To program a memory button:  
1. Do not lift your handset. Press ƒ•‹.  
Program Features  
2. The transient display displays Program Features.  
3. Press a programmable button.  
4. Press ƒ.  
Press a button  
QUIT  
Feature code:  
QUIT  
F_  
QUIT  
5. Enter the feature code number you want to program.  
For example, enter ·°‚ to program the Leave  
Message feature code. For a list of frequently used  
feature codes, refer to the table Description of feature  
CLEAR  
Programmed  
The display shows that the button has been  
programmed.  
Repeat steps 1 to 5 for each Enterprise Edge Voice  
Messaging feature code you want to program.  
Use one of the paper labels that came with your Enterprise Edge telephone to  
identify the programmed button. To use the feature, press the labeled button.  
Mailbox options  
To access the main mailbox menu, refer to the table Main Mailbox menu and  
options on page 25. The main mailbox menu options are described in the table Main  
To access the mailbox administration menu, refer to Mailbox Administration menu  
on page 25. The mailbox administration options are described in the table Mailbox  
Enterprise Edge Voice Messaging Reference Guide  
P0908524 Issue 01  
 
       
Feature codes and mailbox options 2 5  
Main Mailbox menu and options  
To access the main mailbox menu:  
1. Press ƒ·°⁄ to open your mailbox.  
2. Enter your mailbox password and press OK or £.  
Pswd:  
OTHR  
RETRY  
OK  
3. The main mailbox menu options appear. Choose one  
of the options shown in the table below.  
0 new 0 saved  
PLAY REC  
ADMIN  
Table 2 Main Mailbox Options  
Display Button Task Description  
Button  
Found on Page  
PLAY  
REC  
¤
°
--  
ADMIN  
To change mailbox options. Refer to the Mailbox  
--  
--  
To talk to an operator if an operator is available.  
--  
£
Mailbox Administration menu  
To access the Mailbox Administration menu:  
1. Press ƒ·°⁄ to open your mailbox.  
2. Enter your mailbox password and press OK or £.  
Pswd:  
OTHR  
RETRY  
OK  
3. Press ADMIN or °.  
0 new 0 saved  
PLAY REC  
ADMIN  
4. Choose one of the options shown in the table Mailbox  
Mailbox admin  
GREET PSWD QUIT  
P0908524 Issue 01  
Enterprise Edge Voice Messaging Reference Guide  
 
         
2 6 Feature codes and mailbox options  
Table 3 Mailbox Administration Options  
Display  
Button  
Button Task Description  
Found on Page  
--  
¤
GREET  
PSWD  
--  
answers the call if a caller presses 0 during the call. The  
Target Attendant overrides the Designated Operator.  
--  
°
--  
QUIT  
Quitting the Mailbox Administration menu and  
returning to the Main menu.  
Enterprise Edge Voice Messaging Reference Guide  
P0908524 Issue 01  
 
 
Greetings  
5
Introduction  
This chapter describes the mailbox greetings and how to record them. This chapter  
includes:  
Types of mailbox greetings  
The two types of greetings are:  
Personal mailbox greetings (which include Primary, Alternate, and  
Personalized greetings)  
Information mailbox greetings  
Personal mailbox greetings  
Personal mailbox greetings play to callers who reach your mailbox. Greetings  
inform callers that they have reached the correct mailbox and give callers any  
necessary information or instructions. You can change the greetings at any time.  
After you initialize your mailbox, you can record your greetings. If you do not  
record any Personal greetings, your Company Directory name recording plays to  
callers who reach your mailbox. Refer to Recording or changing your name in the  
There are three types of Personal mailbox greetings: Primary, Alternate and  
Personalized.  
Recording technique for personal mailbox greetings  
When you record your Personal greetings, remember to speak clearly and at a pace  
that is easy to understand. After you record a greeting, you can replay it before you  
accept it. You can record or change a greeting from any Enterprise Edge telephone  
or, if you are away from the office, from any touch tone phone. When you record a  
greeting, do not use the Handsfree feature. You have better results if you speak  
directly into the handset.  
P0908524 Issue 01  
Enterprise Edge Voice Messaging Reference Guide  
 
                 
2 8 Greetings  
Primary mailbox greeting  
Record your Primary mailbox greeting for everyday use. In this greeting include  
your name and a brief message explaining to callers that you are unable to answer  
their calls. For example:  
“Hi. This is Paul Wayne. I’m not able to take your call right now. Please leave me  
a message at the tone and I will return your call as soon as possible.”  
If you are a new mailbox owner, record your Primary mailbox greeting  
immediately.  
Alternate mailbox greeting  
The Alternate mailbox greeting is normally used for special circumstances. For  
example:  
“Hi. This is Paul Wayne. I am out of the office until Thursday, the 17th of  
December. Although I am out of the office, I do check my mailbox daily. Please  
leave me a message at the tone and I will return your call as soon as possible. Thank  
you.”  
After it is recorded, you must choose which greeting you want Enterprise Edge  
Voice Messaging to play. You can change the selection at any time, and as often as  
needed.  
Personalized mailbox greeting  
Personalized mailbox greetings are available only if your company subscribes to the  
Caller ID (CLID) service from your local telephone company. For more  
information about CLID, ask your System Administrator.  
A Personalized mailbox greeting plays to callers based on the caller’s phone  
number. Enterprise Edge Voice Messaging recognizes the assigned incoming  
phone number and plays the Personalized mailbox greeting. For example:  
“Hi Susan. I may have missed your call, but I don’t want to miss meeting you for  
lunch. See you at noon.”  
Enterprise Edge Voice Messaging Reference Guide  
P0908524 Issue 01  
 
       
Greetings 2 9  
Information mailbox greetings  
Information mailboxes greetings provide messages and announcements to callers.  
A caller is automatically disconnected after listening to an Information mailbox  
greeting. Information mailboxes can be used to:  
announce sales  
provide product lists  
announce special events  
For example:  
“Paddy’s Dance Studio proudly presents an extravaganza of dance. The  
entertainment begins at 8:00 p.m. on the fourth of July. Toddlers tap is in the White  
Room. Folk dance is in the Green Room. Classical ballet is in the Pink Room.  
Contemporary jazz is in the Blue Room. The Studio and Recital Rooms are located  
at 222 Main Street.”  
Make Information mailboxes easy for a caller to find. Do this by using your  
company Operator or the Automated Attendant Company greetings to route the  
caller. For details about Information mailboxes, ask your System Administrator.  
Information mailboxes are different from Custom Call Routing (CCR) Information  
Mailboxes. Callers must use the CCR Tree to access a CCR Information mailbox.  
For more information about CCR Information Mailboxes, ask your System  
Administrator.  
Recording the Primary or the Alternate mailbox greeting  
This procedure shows you how to record your Primary or Alternate mailbox  
greetings. To start using Enterprise Edge Voice Messaging, only a Primary mailbox  
greeting is necessary. If you do not record any Personal mailbox greetings, your  
Company Directory name recording plays to callers who reach your mailbox.  
If you record both Primary and Alternate mailbox greetings, you must choose which  
greeting plays. If you do not choose a greeting, the Primary mailbox greeting  
automatically plays. For information on how to choose a greeting, refer to Choosing  
P0908524 Issue 01  
Enterprise Edge Voice Messaging Reference Guide  
 
           
3 0 Greetings  
To record your Primary or Alternate mailbox greeting:  
1. Press ƒ·°⁄ to open your mailbox.  
2. Enter your mailbox password and press OK or £.  
Pswd:  
OTHR  
RETRY  
OK  
Note: If you record a mailbox greeting from a  
telephone that has not been assigned to your  
Personal mailbox, press OTHR. The display  
shows the Log: prompt. When this prompt  
appears, enter your mailbox number and  
password.  
If you are using a single-line display telephone,  
press at the Pswd: prompt to show the Log:  
prompt.  
3. Press ADMIN or °.  
4. Press GREET or ¤.  
5. Press REC or .  
0 new 0 saved  
PLAY REC  
ADMIN  
Mailbox admin  
GREET PSWD QUIT  
Greeting options  
REC CHOOSE  
Greeting:  
CFWD  
PERS  
6. Press PRIME or to record the Primary mailbox  
greeting. Press ALT or ¤ to record the Alternate  
mailbox greeting.  
PRIME  
ALT  
Note: If you are changing your greeting, your current  
recorded Primary mailbox greeting begins to  
play.  
7. Press YES or and record your greeting at the tone.  
Record new?  
YES NO  
QUIT  
8. Press OK or £ to end your recording.  
Record greeting:  
RETRY  
OK  
OK  
9. Press OK or £ to accept the greeting. Press PLAY or  
to listen to the greeting. Press RETRY or ¤ to  
erase and re-record the greeting.  
Accept greeting?  
RETRY  
PLAY  
10. Press ® to end this session.  
Mailbox admin  
GREET PSWD QUIT  
Enterprise Edge Voice Messaging Reference Guide  
P0908524 Issue 01  
 
Greetings 3 1  
Choosing the Primary or the Alternate mailbox greeting  
Primary mailbox greeting  
You record a Primary mailbox greeting after initializing your mailbox. If you record  
a Primary and an Alternate mailbox greeting, you need to choose which greeting  
plays. If you do not choose a greeting, the Primary mailbox greeting plays  
automatically.  
Alternate mailbox greeting  
If you choose the Alternate mailbox greeting, you are asked whether the mailbox  
accepts messages. If you choose Y (yes) your mailbox receives messages in the  
normal way.  
If you choose N (no) the following occurs:  
messages cannot be left in the mailbox  
the Alternate mailbox greeting takes precedence over all other greetings  
if a caller presses a button to cut the message short, they hear a voice prompt  
that says this is a special greeting  
if a caller presses a button to send a fax, the fax goes to the general delivery  
mailbox (not your personal mailbox)  
If you choose the Alternate mailbox greeting, remember to change back to the  
Primary mailbox greeting at the appropriate time.  
To choose a Primary or Alternate mailbox greeting:  
1. Press ƒ·°⁄ to open your mailbox.  
2. Enter your mailbox password and press OK or £.  
Pswd:  
OTHR  
RETRY  
OK  
3. Press ADMIN or °.  
0 new 0 saved  
PLAY REC  
ADMIN  
4. Press GREET or ¤.  
Mailbox admin  
GREET PSWD QUIT  
5. Press CHOOSE or ¤ to choose a greeting.  
Greeting options  
REC CHOOSE CFWD  
6. Press PRIME or to choose the Primary mailbox  
greeting. Press ALT or ¤ to choose the Alternate  
mailbox greeting.  
Use greeting:  
PRIME  
ALT  
QUIT  
Note: If you choose the Alternate mailbox greeting,  
go to step 7. If you choose the Primary mailbox  
greeting, go to step 8.  
P0908524 Issue 01  
Enterprise Edge Voice Messaging Reference Guide  
 
     
3 2 Greetings  
7. If you choose the Alternate mailbox greeting, you are  
asked whether the mailbox accepts messages. Press  
CHNG to toggle from yes to no. If you choose Y (yes)  
then the mailbox can receive messages. If you choose  
N (no) messages cannot be left in the mailbox. Press  
OK.  
Accept msgs:Y  
CHNG  
OK  
8. Press ® to end the session.  
Mailbox admin  
GREET PSWD QUIT  
Note: If you have chosen a greeting that is not yet recorded, you are transferred back  
to the greeting options menu to record the greeting.  
Recording a Personalized mailbox greeting  
If your company subscribes to a CLID service, you have the option of recording a  
Personalized mailbox greeting. For more information about CLID, ask your System  
Administrator. The Personalized mailbox greeting plays only for a person calling  
from the phone number that you designate. For the Personalized mailbox greeting  
to play, the phone number you enter must match the caller’s phone number exactly.  
You can record up to three Personalized mailbox greetings, but each greeting can  
be assigned to only one phone number.  
Note: Personalized mailbox greetings do not play if you have recorded and chosen  
the Alternate mailbox greeting. The Alternate mailbox greeting takes  
precedence over all other greetings.  
To record a Personalized mailbox greeting:  
1. Press ƒ·°⁄ to open your mailbox.  
2. Enter your mailbox password and press OK or £.  
Pswd:  
OTHR  
RETRY  
OK  
3. Press ADMIN or °.  
4. Press GREET or ¤.  
5. Press REC or .  
0 new 0 saved  
PLAY REC ADMIN  
Mailbox admin  
GREET PSWD QUIT  
Greeting options  
REC CHOOSE CFWD  
6. Press PERS or to record a Personalized mailbox  
Greeting:  
PRIME  
ALT  
PERS  
OK  
greeting.  
7. Enter a Personalized greeting number of 1, 2, or 3.  
Greeting:  
RETRY  
Enterprise Edge Voice Messaging Reference Guide  
P0908524 Issue 01  
 
     
Greetings 3 3  
8. Press CHNG or .  
Ph: <none>  
CHNG  
OK  
OK  
9. Enter the phone number (maximum 10 digits) to which  
you are assigning the Personalized mailbox greeting.  
Press OK or £ to accept the phone number.  
Ph:  
RETRY  
10. At the tone, record the greeting. Press OK or £ to end  
Record greeting:  
RETRY  
OK  
OK  
the recording.  
11. Press OK or £ to accept the recording. Press PLAY or  
to listen to the recording. Press RETRY or ¤ to  
erase and re-record the greeting.  
Accept greeting?  
RETRY  
PLAY  
12. To record another Personalized mailbox greeting,  
repeat steps 5 to 11. Press ® to end the session.  
Deleting a Personalized mailbox greeting  
If you program Enterprise Edge Voice Messaging with a Personalized mailbox  
greeting that you no longer need, you can delete the Personalized mailbox greeting.  
To delete a Personalized mailbox greeting:  
1. Press ƒ·°⁄ to open your mailbox.  
2. Enter your mailbox password and press OK or £.  
Pswd:  
OTHR  
RETRY  
OK  
3. Press ADMIN or °.  
4. Press GREET or ¤.  
5. Press REC or .  
0 new 0 saved  
PLAY REC  
ADMIN  
Mailbox admin  
GREET PSWD QUIT  
Greeting options  
REC CHOOSE CFWD  
6. Press PERS or to choose a Personalized mailbox  
Greeting:  
PRIME ALT  
PERS  
OK  
greeting.  
7. Enter the Personalized greeting number (1, 2, or 3)  
that you want to delete.  
Greeting:  
RETRY  
8. Press DEL or ¤ to delete the greeting.  
Ph: XXXXXXX  
CHNG  
DEL  
OK  
Press ® to end the session.  
P0908524 Issue 01  
Enterprise Edge Voice Messaging Reference Guide  
 
   
3 4 Greetings  
Recording an Information mailbox greeting  
Before you record your Information mailbox greeting, you must determine what the  
greeting includes. As you prepare your greeting, be sure to include important times  
and dates. Write the greeting down and practice reading it aloud. When you are  
confident the greeting includes everything you want it to, record the greeting. If you  
are using a Enterprise Edge Voice Messaging system with bilingual capability, you  
must record the Information mailbox greeting in both languages.  
An Information mailbox greeting can be either a Primary or an Alternate mailbox  
greeting on page 29 to record an Information mailbox greeting.  
Enterprise Edge Voice Messaging Reference Guide  
P0908524 Issue 01  
 
   
Accessing your messages  
6
Introduction  
This chapter describes accessing your messages and explains the following related  
topics:  
Receiving calls  
Enterprise Edge Voice Messaging can be used by any outside caller and by other  
mailbox owners in your company. When you are away from the office, you can use  
Enterprise Edge Voice Messaging with any touch tone phone. When you are at the  
office, you can use Enterprise Edge Voice Messaging from any Enterprise Edge  
telephone connected to your company’s Enterprise Edge Voice Messaging system.  
Even outside callers using a rotary dial telephone are able to use Enterprise Edge  
Voice Messaging. When a caller uses Enterprise Edge Voice Messaging from a  
rotary dial telephone, the system transfers the call to your company receptionist or  
the Operator. If a receptionist or the Operator is not available to answer the call, the  
call transfers to the General Delivery mailbox.  
Enterprise Edge Voice Messaging Never Full mailbox feature  
The Never Full mailbox feature lets external callers leave a message in your  
mailbox, even if the mailbox is technically “full”. The message is stored in your  
mailbox, but cannot be accessed until you delete at least one existing message to  
allow space for the new message. If you attempt to listen to any new messages  
before deleting an existing message, you hear this voice announcement:  
“Your mailbox is full. You must erase some messages before you can listen to new  
messages.”  
You are not able to leave a message in another mailbox, create a new message,  
Copy, Send, or Reply to a message, until you delete at least one existing message.  
The Never Full mailbox feature is not available to internal callers. Internal callers  
cannot leave messages in mailboxes that are technically “full”.  
P0908524 Issue 01  
Enterprise Edge Voice Messaging Reference Guide  
 
                           
3 6 Accessing your messages  
Listening to your mailbox messages  
To listen to your messages:  
1. Press ƒ·°⁄ to open your mailbox.  
2. Enter your mailbox password and press OK or £.  
Pswd:  
OTHR  
RETRY  
OK  
3. Press PLAY to listen to your messages. For options,  
2 new 0 saved  
PLAY  
REC  
ADMIN  
refer to the table Listening to your mailbox messages.  
4. Press ® to end the session.  
A number of options are available to you during and after listening to a message.  
The table Listening to your mailbox messages shows the options and when they are  
available.  
Listening to your mailbox messages  
Option  
Button  
Available  
while  
Available Description  
after  
listening to a listening to  
message  
a message  
Backup  
Copy  
X
Rewinds the message nine seconds and resumes  
playing it from that point.  
or  
< <<  
X
X
Sends a copy of the message to one or more  
mailboxes. When you record the introduction to  
the forwarded message, the introduction must be  
more than three seconds long.  
or  
COPY  
End of  
Message  
X
X
Skips to the end of the message.  
‹‹  
or  
> >> > >>  
Envelope  
Erase  
X
X
Plays the information in the message envelope.  
Envelope information includes the date and time  
the message was sent and, if the message was  
internal, the directory name of the sender. This  
option is not shown on the display.  
X
X
Deletes the message currently being played or, if  
no messages are playing, deletes the message just  
played. Deleted messages remain in your mailbox  
until the session is ended. (Refer to Notes 1. and  
2.)  
°
or  
ERASE  
Forward  
Advances the message nine seconds and  
continues playing from that point. A message can  
be forwarded as many times as required.  
or  
> >>  
Enterprise Edge Voice Messaging Reference Guide  
P0908524 Issue 01  
 
                   
Accessing your messages 3 7  
Listening to your mailbox messages  
Option  
Button  
Available  
while  
Available Description  
after  
listening to a listening to  
message  
a message  
Next  
X
X
Plays the next message in your mailbox. If used  
while a message is playing, it stops playing the  
current message and plays the next message in  
your mailbox. This option is not shown on the  
display.  
or  
££  
Pause/  
Continue  
X
X
Stops a message temporarily. When you stop the  
message, you have the option to play the previous  
message, continue playing the current message,  
or skip to the next message.  
¤
or  
STOP/PLAY  
Previous  
X
X
Stops playing the current message and begins  
playing the previous message. This option is not  
shown on the display.  
Quit  
Stops playing the message and plays the Mailbox  
main menu options.  
Replay  
⁄⁄  
or  
X
Goes back to the beginning of the message and  
plays the message again.  
< << < <<  
Replay  
Reply  
X
X
Replays the last message. This option is not  
shown on the display.  
X
X
Replies to a message. (Refer to Note 3.)  
The reply can be either:  
·
or  
- a message to an internal sender’s mailbox  
REPLY  
- a telephone call to an internal or external  
party (Refer to Note 4.)  
Save  
Message  
Saves the message being played. (If you do not  
delete a message, it is automatically saved). This  
option is not shown on the display unless you  
erase a message. If you erase a message, and play  
the message again, you are given the option to  
press SAVE on an Enterprise Edge two line  
display telephone. (Refer to Note 2.)  
‡‡  
or  
SAVE  
Volume  
Control  
X
Adjusts the volume of the message that is  
playing. The volume increases each time you  
press . After four consecutive presses, the  
volume returns to the lowest level. This option is  
not shown on the display.  
P0908524 Issue 01  
Enterprise Edge Voice Messaging Reference Guide  
 
               
3 8 Accessing your messages  
Notes:  
1. Because your mailbox has limited message storage space, delete any messages  
you no longer need. After a certain time period, your saved messages may be  
erased automatically. Ask your System Administrator about this.  
2. You can retrieve a deleted message only if you have not quit the session in  
which you deleted it. Locate the deleted message. Then play (press ⁄⁄)  
and save (press ‡‡ or SAVE) the message. For further information about  
retrieving deleted messages refer to About erased messages.  
3. Applies only if the Reply feature is enabled.  
4. You can reply to an outside caller by dialing them back if your company  
subscribes to Caller ID (CLID) service. For further information about replying  
About erased messages  
After listening to your messages and exiting Enterprise Edge Voice Messaging, all  
messages that you do not erase are automatically saved. Since message storage  
space is limited, we recommend that you erase messages that are no longer needed.  
You can retrieve an erased message if you are still in the Enterprise Edge Voice  
Messaging session. An erased message remains in your mailbox until you end the  
current Enterprise Edge Voice Messaging session.  
After you erase a new or saved message, the number of new or saved messages  
shown on the display is decreased by one. Even though the display may show 0 new  
0 saved, you can still play and retrieve your erased messages. Press PLAY or ¤ to  
listen to your erased message. Refer to the table Listening to your mailbox messages  
After you play your erased message, you are given the option to save it. If you end  
the current session without saving the erased message, it is permanently deleted  
from Enterprise Edge Voice Messaging.  
Enterprise Edge Voice Messaging Reference Guide  
P0908524 Issue 01  
 
             
Accessing your messages 3 9  
Call Screening  
Call Screening lets you determine who is calling before you accept the call. It  
applies only to external calls transferred from the Automated Attendant or from  
Custom Call Routing (CCR). See your System Administrator for information on  
CCR.  
Call Screening is useful in the following circumstances:  
if CLID is not available  
if CLID is not a reliable indication of the caller identity  
if your Enterprise Edge telephone does not have display capabilities  
The System Administrator enables the Call Screening feature for your Enterprise  
Edge Voice Messaging system.  
If Call Screening is unavailable, the call transfers immediately for the following  
types of calls:  
internal calls  
external calls placed directly to your phone number  
external calls for which you have established a Personalized greeting  
How to use Call Screening  
To use the Call Screening feature:  
1. You receive an external call that is transferred from the Automated Attendant  
or from Custom Call Routing (CCR).  
2. Enterprise Edge Voice Messaging announces the caller’s name to you. If the  
caller chooses not to record their name, the voice prompt says, “Unknown  
caller.”  
3. You have the option of accepting the call or having the caller leave a message  
in your Enterprise Edge Voice Messaging mailbox:  
• press ANS or to accept the call  
• press QUIT or to transfer the call to your Enterprise Edge Voice Messaging  
mailbox (and the caller is informed that you are not available).  
If Call Screening is enabled, Enterprise Edge Voice Messaging asks the caller to  
record their name after the tone. (If the caller presses when they are asked to  
record their name, the call goes back to the Automated Attendant.) The caller hears  
a hold tone while they wait. If you do not answer, the caller is informed that you are  
not available, and the call transfers to your mailbox.  
Since some callers may not like recording their name and waiting for service, use  
this feature with discretion.  
P0908524 Issue 01  
Enterprise Edge Voice Messaging Reference Guide  
 
             
4 0 Accessing your messages  
Enterprise Edge Voice Messaging Reference Guide  
P0908524 Issue 01  
 
Sending messages  
7
Introduction  
This chapter describes sending messages and explains the following topics:  
Types of messages  
There are two types of messages, Broadcast messages and Personal messages.  
Broadcast messages  
There might be times when you open your Personal mailbox and a message plays  
immediately. This is a Broadcast message left by your System Administrator. This  
type of message can be sent only by your System Administrator. Make sure you  
listen to the entire message. After it plays, the message is automatically erased from  
your mailbox.  
Personal messages  
Sending personal messages to a mailbox  
send a message when you do not know the person’s mailbox number, use the  
Company Directory. Refer to Using the Company Directory on page 42.  
Personal messages addressed to a Group List  
You can send a message to a group of people by addressing a message to a Group  
List. For more information, refer to Sending a message using a Group List on page  
P0908524 Issue 01  
Enterprise Edge Voice Messaging Reference Guide  
 
                   
4 2 Sending messages  
About recording and sending a message  
Messages can be recorded and sent using:  
the Open Mailbox feature (ƒ·°⁄)  
the Leave Message feature (ƒ·°‚)  
When you use the Open Mailbox feature, you open your personal mailbox and enter  
your password. Then you record your message and enter the extension of the  
message recipient.  
The Leave Message feature prompts you to enter the extension of the message  
recipient immediately. Then you record your message. No password is required  
because you do not open a mailbox.  
Both features allow you to:  
use the Company Directory (refer to Using the Company Directory)  
assign message delivery options (refer to Message delivery options on page 44)  
send a message to more than one recipient (refer to Sending a message to more  
Using the Company Directory  
You can find any initialized mailbox by searching the Company Directory. Use the  
Company Directory if you do not know the mailbox number of someone you want  
to send a message to. You can access the Company Directory if:  
the display shows DIR  
the voice prompt announces, “Press £ to use the Directory.”  
you are prompted to choose a mailbox  
The Company Directory option is available from both the Open Mailbox feature  
and the Leave Message feature.  
Enterprise Edge Voice Messaging Reference Guide  
P0908524 Issue 01  
 
               
Sending messages 4 3  
To access the Company Directory using the Leave Message feature:  
1. Press DIR or £ to use the Company Directory.  
Mbox:  
DIR  
QUIT  
OK  
2. Use the dialpad buttons associated with the first three  
or four letters of the mailbox owner’s name to locate  
and select the person’s mailbox. (Enter the last name,  
first name or both names depending on how your  
system is set up. This display shows an example of a  
prompt for a mailbox owner’s last name.) You do not  
need to enter a comma. Press OK or £.  
Last name:  
For example, to enter the letters “Wayn”  
press ·¤·fl. If the mailbox owner has fewer  
than four letters in their last name, press the buttons on  
the dialpad to spell out the entire last name, and press  
OK or £. For more information, refer to Entering  
3. In this example, the name of the mailbox owner, Paul  
Wayne appears on the display and is announced. To  
accept the mailbox owner, press OK or £.  
Wayne, Paul  
RETRY  
NEXT  
OK  
If you do not want the person who is shown, press  
NEXT or to see the next matching name.  
4. The greeting of the mailbox owner plays. If the  
mailbox owner you selected does not have a Personal  
greeting recorded and selected, you hear their  
Company Directory recording.  
Wayne, Paul  
P0908524 Issue 01  
Enterprise Edge Voice Messaging Reference Guide  
 
4 4 Sending messages  
Message delivery options  
Enterprise Edge Voice Messaging provides you with five possible message delivery  
options:  
Normal  
Certified  
Urgent  
Private  
Timed Delivery  
Option  
Display Button Button  
Description  
Send  
SEND  
£ or ®  
Sends a message with Normal delivery  
option.  
Certified  
Urgent  
CERT  
Sends you notification that your message  
has been received and played.  
URGENT  
Plays messages marked Urgent before other  
messages left in the mailbox. Urgent  
messages are preceded by the voice prompt,  
This message is urgent”.  
¤
Other  
OTHR  
Accesses the Private and Timed delivery  
options. If PRIV appears instead of OTHR,  
the Timed delivery option is not available.  
Private  
Timed  
PRIV  
TIME  
Private messages cannot be forwarded to  
another mailbox.  
Allows you to assign the time that the  
message is received.  
Normal, Certified, and Private messages play in the order they are received. Urgent  
messages play before other messages left in the mailbox, except for Broadcast  
messages. (Refer to Broadcast messages on page 41.) The Certified and Timed  
delivery options are available only if you call from a telephone that has a mailbox  
associated with it. Messages sent with the Timed delivery option are played at the  
time that you specify.  
If you use the Timed delivery option, you first enter the time, including a.m. or p.m.  
You are then prompted to accept or change the date, which defaults to today or  
tomorrow, and you can accept the date that corresponds to the next occurrence of  
the specified time. Dates are shown by month and day, and the year is inferred. If  
the month and day are earlier than the current date, the next year is assumed. When  
the specified time and date occurs, the message is sent. You cannot cancel the  
message prior to delivery.  
Enterprise Edge Voice Messaging Reference Guide  
P0908524 Issue 01  
 
                     
Sending messages 4 5  
Assigning message delivery options using the Open Mailbox feature  
To assign message delivery options using the Open Mailbox feature:  
1. Press CERT or to assign the Certified delivery  
Delivery options  
CERT URGENT OTHR  
option. Press URGENT or ¤ to assign the Urgent  
delivery option. Press OTHR to assign the Private or  
Timed delivery options. If PRIV appears instead of  
OTHR, the Timed delivery option is not available.  
Note: The OTHR display button is not available or  
required for single-line display telephones.  
You can access the Private and Timed  
Delivery options by pressing the dialpad  
buttons on either a two-line or a single-line  
display telephone.  
2. Press PRIV or to send a message with a Private  
Delivery options  
PRIV  
TIME  
delivery option. If you press PRIV or , go to step 7.  
If you want to send a message with the Timed delivery  
option press TIME or . If you press TIME or ,  
continue with step 3.  
3. Enter the time that you want to send a message using  
Time hhmm:  
RETRY  
the Timed delivery option.  
Note: This is a four digit field. Any single-digit hour  
or minute must be preceded by a zero. For  
example, enter 0800 for eight o’clock.  
4. Press AM or or PM or ¤.  
hh:mm  
RETRY  
AM  
PM  
OK  
5. Press OK or £ to accept the time you entered or press  
hh:mm am/pm  
RETRY  
RETRY or to change the time.  
6. Press CHNG or to change the date shown to a  
different date. Press NXTDAY to change the date to the  
next day (the day after the date that is shown). Press  
OK or £ to accept the date shown, which defaults to  
today or tomorrow, and select the one that corresponds  
to the next occurrence of the specified time.  
Tu mm dd  
CHNG  
NXTDAY OK  
7. Press SEND or £ to send this message now. Press •  
Wayne, Paul  
OPTS  
CC  
SEND  
to cancel all delivery options.  
Press ® to end this session.  
P0908524 Issue 01  
Enterprise Edge Voice Messaging Reference Guide  
 
   
4 6 Sending messages  
Assigning message delivery options using the Leave Message feature  
To assign message delivery options using the Leave Message feature:  
1. Press ƒ·°‚.  
2. Enter the mailbox number or Group List number of the  
person or Group you want to leave a message for. If  
you do not know the mailbox number, press DIR or £  
to use the Company Directory.  
Mbox:  
DIR  
QUIT  
3. At the sound of the tone, record your message. Press  
PAUSE or ¤ to pause during your recording. When  
you pause, press CONT or ¤ to continue recording  
your message. Press OK or £ to end your recording.  
Press RETRY to erase and re-record your message.  
Record message:  
RETRY PAUSE  
OK  
4. Press PLAY or to listen to your message before  
sending it. Press RETRY or ¤ to erase and re-record  
your message. Press to access delivery options.  
Press SEND or £ to send your message now.  
Message options:  
RETRY PLAY SEND  
Recording and sending a message using the Open Mailbox feature  
To record and send a message using the Open Mailbox feature:  
1. Press ƒ·°⁄ to open your mailbox.  
2. Enter your mailbox password and press OK or £.  
Pswd:  
OTHR  
RETRY  
OK  
3. Press REC or and record your message at the tone.  
0 new 0 saved  
PLAY REC  
ADMIN  
4. Record your message. Press PAUSE or ¤ while  
recording your message to stop temporarily. When you  
wish to resume recording, press CONT or ¤ to  
continue recording your message. Press OK or £ to  
end your recording. Press RETRY to erase and re-record  
your message.  
Record message:  
RETRY PAUSE  
OK  
5. Press OK or £ to accept your message. Press PLAY or  
to listen to your message. Press RETRY or ¤ to  
erase and re-record your message.  
Accept rec?  
RETRY PLAY  
OK  
Enterprise Edge Voice Messaging Reference Guide  
P0908524 Issue 01  
 
       
Sending messages 4 7  
6. Enter the mailbox number or Group List number of the  
person or Group you want to leave a message for. If  
you do not know the mailbox number, press DIR or £  
to use the Company Directory.  
Mbox:  
DIR  
QUIT  
SEND  
7. Press SEND or £ to send the message now with the  
Normal delivery option. Press OPTS or for delivery  
options. Press CC or to send this message to more  
than one mailbox owner, with one set of delivery  
options applied to all recipients.  
Wayne, Paul  
OPTS  
CC  
Note: The display shows the name of the mailbox  
owner or Group (in this example, mailbox  
owner Paul Wayne).  
Press ® to end this session.  
0 new 8 saved  
PLAY REC  
ADMIN  
Recording and sending a message using the Leave Message feature  
To record and send a message using the Leave Message feature:  
1. Press ƒ·°‚.  
2. Enter the mailbox number or Group List number of the  
person or Group you want to leave a message for. If  
you do not know the mailbox number, press DIR or £  
to use the Company Directory.  
Mbox:  
DIR  
QUIT  
3. At the sound of the tone, record your message. Press  
Record message:  
RETRY PAUSE  
OK  
OK or £ to end your message.  
4. Press SEND or £ or replace the receiver to send the  
message using the Normal Delivery Option. Press  
PLAY or to listen to your message. Press RETRY or  
¤ to erase and re-record your message. Press to  
change the Delivery Options.  
Message options:  
RETRY PLAY SEND  
P0908524 Issue 01  
Enterprise Edge Voice Messaging Reference Guide  
 
   
4 8 Sending messages  
Replying to messages  
You can reply to internal message senders and to external message senders. To  
reply to a message from an external message sender, your company must subscribe  
to Caller ID (CLID).  
Replying to an internal message sender  
You can reply to a message from an internal message sender by:  
1. Using the CALL option. If you select CALL, you are immediately transferred to  
the internal message sender’s extension. You must have an initialized  
Enterprise Edge Voice Messaging mailbox and an operating directory to use  
the CALL option.  
2. Using the MSG option. If you select the MSG option, begin recording your reply  
at the tone.  
To reply to an internal message sender:  
1. Press ƒ·°⁄ to open your mailbox.  
2. Enter your mailbox password and press OK or £.  
Pswd:  
OTHR  
RETRY  
OK  
3. Press PLAY or ¤.  
1 new 0 saved  
PLAY REC  
ADMIN  
4. After you have listened to your message, press REPLY  
End of message  
REPLY ERASE NEXT  
or ·.  
5. Press CALL or ¤ to call the message sender  
or  
Reply to msg  
MSG  
CALL  
QUIT  
press MSG or to record and send a reply.  
Enterprise Edge Voice Messaging Reference Guide  
P0908524 Issue 01  
 
           
Sending messages 4 9  
Replying to an external message sender  
You can reply to a message from an external message sender if your company  
subscribes to CLID. Before using the Reply option you must play the message.  
To reply to an external message sender:  
1. Press ƒ·°⁄ to open your mailbox.  
2. Enter your mailbox password and press OK or £.  
Pswd:  
OTHR  
RETRY  
OK  
3. Press PLAY or ¤.  
1 new 0 saved  
PLAY REC  
ADMIN  
4. Press REPLY.  
End of message  
REPLY ERASE NEXT  
5. Enterprise Edge Voice Messaging dials the external  
number directly.  
After you call the message sender, your session ends.  
Sending a message to more than one recipient  
Sending a message using a Group List  
A Group List is a collection of mailbox owners. When you send a message to a  
Group List, each mailbox owner in the Group List receives the same message. If  
you are a member of the group you are addressing, you do not receive a copy of the  
message.  
If you would like a Group List for your specific needs, ask your System  
Administrator to create a Group List for you. Include the following information for  
the System Administrator:  
the mailbox owners’ names  
a list of the mailbox numbers  
the Group List name  
Your System Administrator can publish a list of the mailboxes in each Group List.  
You can enter the Group List number instead of a mailbox number at the Mbox:  
prompt. You can also enter the name of the Group List in the Company Directory  
at the DIR prompt.  
P0908524 Issue 01  
Enterprise Edge Voice Messaging Reference Guide  
 
             
5 0 Sending messages  
Copying a message to other recipients  
You can copy a message to other recipients using the Open Mailbox feature:  
using ALL - message recipients have the same delivery options  
using CC - this allows message recipients to have different delivery options  
Note: You cannot copy a message to other recipients using the Leave Mailbox  
feature. You cannot copy Private messages.  
Forwarding a copy of a message to one or more recipients  
From the Main Mailbox menu you can forward a copy of a message during or after  
playing the message. When you forward a copy of a message to a mailbox, you are  
prompted to record an introduction to the message. Your introduction has to be at  
least three seconds long.  
When you record an introduction and enter the mailbox number, your introduction  
and a copy of the message are automatically sent to the mailbox you selected. You  
then have options to send an additional copy of the introduction and the message to  
another mailbox, or to quit and return to the Listen to Messages menu. You can  
forward copies to as many mailboxes as you want. (Messages marked Private  
cannot be forwarded to another mailbox.)  
For more information on playing your messages, refer to Listening to your mailbox  
Copying a message is not the same as forwarding a message using the Copy option.  
Copied messages do not have recorded introductions. Refer to Copying a message  
Enterprise Edge Voice Messaging Reference Guide  
P0908524 Issue 01  
 
               
Call Forwarding your calls  
8
Introduction  
This chapter shows the following ways that you can forward your calls:  
Call Forwarding your calls to Enterprise Edge Voice Messaging  
To forward incoming calls to your mailbox, press ƒ·°›.  
To cancel Call Forward, do one of the following:  
press ∞  
press ƒ£›  
press CANCEL  
Setting up Call Forward remotely  
When you are away from the office, you can forward your calls to your Enterprise  
Edge Voice Messaging mailbox by using the dialpad of any touch tone phone.  
To access your Personal mailbox from another location and set up Remote Call  
Forward:  
1. Call the Automated Attendant or your Enterprise Edge telephone from any  
touch tone phone and press •• while the greeting plays.  
2. Enter your mailbox number and password and press £.  
3. Press °.  
4. Press ¤.  
5. Press to turn call forwarding from the Call Forward menu on and off.  
6. Press to turn Call Forward on and off.  
Note: If Call Forward is turned on, the voice prompt says: “Calls will be  
answered immediately.” All calls to your telephone are now answered  
by Enterprise Edge Voice Messaging.  
If Call Forward is turned off, the voice prompt says: “Calls will ring at  
your set.”  
P0908524 Issue 01  
Enterprise Edge Voice Messaging Reference Guide  
 
               
5 2 Call Forwarding your calls  
7. Press to turn Call Display on and off.  
Note: If Call Display is turned on, the voice prompt says: “Caller  
information will be displayed at your set.”  
If Call Display is turned off, the voice prompt says: “Caller  
information will not be displayed.”  
8. Replace the handset to end this session.  
Call Forward with Caller ID (CLID)  
The Call Forward with CLID feature is available only if your company subscribes  
to CLID service. If you are not sure whether your company subscribes to CLID  
service, ask your System Administrator. CLID does not appear if the caller has a  
private or unknown phone number.  
You can set up Call Forward with CLID to screen calls forwarded to your Enterprise  
Edge Voice Messaging mailbox. If the feature is enabled, you hear an Alert tone and  
the CLID information appears on the telephone display.  
To talk to the caller who has been forwarded to your mailbox, press  
ƒ·°‡ to interrupt the call.  
To turn Call Forward with CLID on and off:  
1. Press ƒ·°⁄ to open your mailbox.  
2. Enter your mailbox password and press OK or £.  
Pswd:  
OTHR  
RETRY  
OK  
3. Press ADMIN or °.  
0 new 0 saved  
PLAY REC  
ADMIN  
4. Press GREET or ¤.  
Mailbox admin  
GREET PSWD QUIT  
5. Press CFWD or .  
Greeting options  
REC CHOOSE CFWD  
6. Press CHNG or to turn Call Forward on and off.  
7. Press CHNG or to turn Call Display on and off.  
8. Press ® to end the session.  
Forward calls:Y  
CHNG  
NEXT  
Display caller:Y  
CHNG  
NEXT  
Mailbox admin  
GREET PSWD QUIT  
Enterprise Edge Voice Messaging Reference Guide  
P0908524 Issue 01  
 
         
Call Forwarding your calls 5 3  
Call Forward on Busy overrides CLID  
If your Enterprise Edge telephone is assigned Call Forward on Busy, CLID  
information does not appear on the display. Call Forward on Busy is a feature that  
forwards all of your calls to another designated telephone or extension if your  
telephone is busy. Call Forward on Busy is assigned by the Enterprise Edge System  
Administrator.  
P0908524 Issue 01  
Enterprise Edge Voice Messaging Reference Guide  
 
   
5 4 Call Forwarding your calls  
Enterprise Edge Voice Messaging Reference Guide  
P0908524 Issue 01  
 
Transferring calls  
9
Introduction  
This chapter describes transferring calls and explains:  
Transferring calls to an Enterprise Edge Voice Messaging mailbox  
Any time a caller wants to leave a message in a mailbox, you can easily transfer  
their call from your Enterprise Edge telephone to any mailbox initialized with  
Enterprise Edge Voice Messaging.  
Transferring calls to an Enterprise Edge Voice Messaging mailbox has the  
following advantages:  
If you transfer a call to a mailbox instead of another telephone, the call does not  
come back to you. If you transfer a call to another telephone and the call is not  
answered, the call does comes back to you.  
The call is immediately transferred to the mailbox (which saves time).  
ƒ·°fl is not available on the Enterprise Edge Companion Wireless  
telephone.  
P0908524 Issue 01  
Enterprise Edge Voice Messaging Reference Guide  
 
           
5 6 Transferring calls  
To transfer a call to a mailbox from your Enterprise Edge telephone:  
1. Press ƒ·°fl. Do not press ˙ because the call is put on  
hold automatically.  
2. Enter the mailbox number or use the Company Directory by pressing DIR.  
Note: Press OK or £ to accept a name when using the Company Directory.  
Do not use the Internal Autodial feature.  
3. Wait until the display shows Call transferred before attempting any other  
Enterprise Edge Voice Messaging functions. The call is automatically  
transferred and the Enterprise Edge Voice Messaging session ends.  
Transferring a mailbox owner’s call to Enterprise Edge Voice Messaging  
You can transfer a mailbox owner’s call to their Enterprise Edge Voice Messaging  
mailbox so that they can change their greetings or retrieve their messages.  
Note: ƒ·°fl is not available on the Enterprise Edge Companion  
Wireless telephone.  
To transfer a mailbox owner’s call to their Enterprise Edge Voice Messaging  
mailbox from your Enterprise Edge telephone:  
1. Press ƒ·°fl. Do not press ˙.  
2. Enter the mailbox owner’s mailbox number.  
3. Wait until the display shows Call transferred before attempting any other  
Enterprise Edge Voice Messaging functions. The call is automatically  
transfers and the Enterprise Edge Voice Messaging session ends.  
Note: Do not use ƒ‡‚ to transfer a mailbox owner’s call. This  
feature transfers the call to their telephone and the call comes back to  
you.  
After a mailbox owner’s call transfers to their mailbox, the mailbox owner must:  
1. Press •• while their Personal greeting plays.  
2. Enter their mailbox number and password and press £.  
3. Follow the voice prompts.  
Enterprise Edge Voice Messaging Reference Guide  
P0908524 Issue 01  
 
   
Transferring calls 5 7  
Transferring calls from your mailbox to the Operator  
To transfer calls from your mailbox to the Operator, press while at the Main  
Mailbox menu. For more information, refer to Main Mailbox menu and options on  
Transferring calls from your mailbox to the Automated Attendant  
To transfer to the Automated Attendant from your mailbox, press £ at the Main  
Mailbox menu. For more information, refer to Automated Attendant on page 13 and  
Transferring a call to Custom Call Routing (CCR)  
About Custom Call Routing (CCR)  
Custom Call Routing (CCR) is a single-digit application that provides callers with  
a more sophisticated menu and a wider range of options. Using CCR, a caller can:  
listen to the Home menu and make a selection  
listen to a pre-recorded CCR Information message  
leave a message in a mailbox  
transfer to another extension or an external number  
For more information about CCR, ask your System Administrator.  
A call can be transferred to the beginning of a CCR Tree. To transfer a call to a CCR  
Tree:  
1. Press ƒ·°fl. Do not press ˙.  
2. Choose a CCR Tree by entering a digit from 1 to 4 and pressing £.  
3. Wait until the display shows Call transferred before attempting any other  
Enterprise Edge Voice Messaging functions. The call automatically transfers  
and the Enterprise Edge Voice Messaging session ends.  
P0908524 Issue 01  
Enterprise Edge Voice Messaging Reference Guide  
 
                     
5 8 Transferring calls  
Outbound Transfer  
You can set up Outbound Transfer to transfer a caller who has reached your mailbox  
to a number that you assign. A caller can use Outbound Transfer from any touch  
tone telephone, and you can direct your Outbound Transfer calls to any telephone.  
You can personally inform callers of this feature, or you can inform callers of this  
feature in your personal greeting. If you choose to inform callers of this feature in  
your mailbox greeting, you must tell them to press to be transferred. For  
example:  
“Hi. This is Brenda Whately. I’m away from the office today. Please leave me a  
message after the tone and I will return your call as soon as possible. If you need  
to reach me before tomorrow, press and you will be transferred to my cellular  
phone. Thanks.”  
Note: The restrictions that apply to your telephone line also apply to Outbound  
Transfer numbers. For example, if you are unable to dial long distance  
phone numbers from your telephone, you cannot have a long distance  
Outbound Transfer destination.  
If your mailbox is restricted to extension destinations for Outbound  
Transfer, see your System Administrator.  
For Outbound Transfer to function properly, you must have a greeting recorded.  
When you set up Outbound Transfer, you can add special characters to the  
refer to the following tables and examples.  
Adding special characters to the destination number  
Follow the voice prompts or press ADD to add special characters to a destination  
phone number (or a destination pager number if you are setting up a destination  
pager number in Off-premise Message Notification. The destination pager number  
cannot be longer than 29 characters.) The destination phone number cannot be  
longer than 30 characters.  
Note: If you are adding special characters, do not press the dialpad buttons  
£ to enter a #, or to enter a *. Press the button directly below the  
option on a two-line display telephone, or listen to the voice prompts.  
Enterprise Edge Voice Messaging Reference Guide  
P0908524 Issue 01  
 
           
Transferring calls 5 9  
To add special characters on an Enterprise Edge one line display telephone, refer to  
telephone. To add special characters on a two-line display telephone, refer to the  
Table 4 Adding special characters using an Enterprise Edge one line display telephone  
Press  
Description  
to retry or add digits to the destination phone number.  
¤
to enter a timed pause that appears as P on the display. Pauses are four seconds  
long.  
to recognize dial tone (behind PBX). The Recognize Dial Tone special  
character appears as D on the display.  
to enter a #.  
to enter a *.  
to cancel and retry.  
Adding special characters using an Enterprise Edge two line display telephone  
Press  
Description  
to cancel and retry.  
DIGS or ¤  
to retry or add digits to the destination phone number.  
PAUS or ‹  
to enter a timed pause that appears as P on the display. Pauses are  
four seconds long.  
OTHR  
TONE  
to go to the next display to enter the following special characters:  
to recognize dial tone (behind PBX). The Recognize Dial Tone  
special character appears as D on the display.  
#
*
to enter a #.  
to enter a *.  
P0908524 Issue 01  
Enterprise Edge Voice Messaging Reference Guide  
 
   
6 0 Transferring calls  
Optimizing Outbound Transfer  
When Enterprise Edge Voice Messaging transfers a call to an external telephone  
number using Outbound Transfer, two lines are used. An incoming line is used to  
connect the caller to your mailbox and an outgoing line is used to transfer the caller  
to your Outbound Transfer telephone number. Both lines remain in use while the  
caller connects to the Outbound Transfer telephone number.  
To optimize the use of Enterprise Edge Voice Messaging lines, the Outbound  
Transfer call to an external telephone number can transfer to the incoming line to  
make the outgoing call. This type of transfer is called a Link transfer.  
Note: A Link transfer can be performed only if the Enterprise Edge Voice  
Messaging line is equipped with Link transfer capability. If a Link transfer  
is programmed for an Outbound Transfer and your Enterprise Edge Voice  
Messaging lines do not support this feature, the caller disconnects. Ask your  
System Administrator before programming the Link transfer.  
To perform a Link transfer with Outbound Transfer you must add a £ before the  
Outbound Transfer telephone number. For example, the telephone number would  
look like:  
£fififi⁄¤‹›  
where:  
£ instructs Enterprise Edge Voice Messaging to use the incoming line to perform  
the transfer  
fi⁄¤‹› is the telephone number dialed  
Programming an Outbound Transfer telephone number when Enterprise Edge  
Voice Messaging is behind PBX or Centrex+  
When Enterprise Edge Voice Messaging is installed behind a PBX or Centrex+ and  
you want to access an outside line and recognize dial tone, enter:  
·£›¤fififi⁄¤‹›  
where:  
· accesses an outside line  
£ specifies the next digits are special characters  
recognizes dial tone  
¤ specifies the next digits are numbers to be dialed  
fififi⁄¤‹› is the phone number dialed  
Enterprise Edge Voice Messaging Reference Guide  
P0908524 Issue 01  
 
     
Transferring calls 6 1  
Setting up Outbound Transfer to a phone number  
To set up Outbound Transfer to a phone number for the first time:  
1. Press ƒ·°⁄ to open your mailbox.  
2. Enter your mailbox password and press OK or £.  
Pswd:  
OTHR  
RETRY  
OK  
3. Press ADMIN or °.  
0 new 0 saved  
PLAY REC  
ADMIN  
4. Press ° to open the Outbound Transfer (xfr) menu.  
5. Press ADMIN or to set up Outbound Transfer.  
Mailbox admin  
GREET PSWD QUIT  
Outbound xfr  
ADMIN  
SELECT  
OK  
6. Enter the destination phone number and press OK or  
Ph:  
RETRY  
£.  
7. Press OK or £ to accept the destination number  
(represented by the <x>). Press ADD or ¤ to add  
special characters. For information, refer to Adding  
58. After you add special characters, press OK or £ to  
accept the destination number.  
<x>  
ADD  
OK  
8. Press CHNG or to turn Outbound Transfer on.  
Transfer: off  
CHNG  
QUIT  
QUIT  
9. Press QUIT or . Press ® to end this session.  
Transfer: on  
CHNG  
Setting up Outbound Transfer to an extension  
To set up Outbound Transfer to an extension for the first time:  
1. Press ƒ·°⁄ to open your mailbox.  
2. Enter your mailbox password and press OK or £.  
3. Press ADMIN or °.  
Pswd:  
OTHR  
RETRY  
OK  
0 new 0 saved  
PLAY REC  
ADMIN  
4. Press ° to open the Outbound Transfer (xfr) menu.  
Mailbox admin  
GREET PSWD QUIT  
P0908524 Issue 01  
Enterprise Edge Voice Messaging Reference Guide  
 
       
6 2 Transferring calls  
5. Press ADMIN or to set up Outbound Transfer.  
6. Enter the destination extension and press OK or £.  
7. Press OK or £ to accept the number.  
Outbound xfr  
ADMIN  
SELECT  
OK  
Ext:  
RETRY  
Accept:<x>  
RETRY  
OK  
Note: The <x> represents the extension.  
8. Press CHNG or to turn Outbound Transfer on.  
Transfer: off  
CHNG  
QUIT  
QUIT  
9. Press QUIT or . Press ® to end this session.  
Transfer: on  
CHNG  
Changing the Outbound Transfer parameters  
To change the Outbound Transfer parameters:  
10. Press CHNG or .  
<x>  
CHNG  
NEXT  
Note: The <x> represents the current Outbound  
Transfer destination number.  
Enterprise Edge Voice Messaging Reference Guide  
P0908524 Issue 01  
 
     
Transferring calls 6 3  
Turning Outbound Transfer on and off  
You can turn Outbound Transfer on or off at any time after you set it up. Turning  
Outbound Transfer off does not affect any of its assigned parameters.  
To turn Outbound Transfer on or off:  
1. Press ƒ·°⁄ to open your mailbox.  
2. Enter your mailbox password and press OK or £.  
Pswd:  
OTHR  
RETRY  
OK  
3. Press ADMIN or °.  
0 new 0 saved  
PLAY REC  
ADMIN  
4. Press ° to open the Outbound Transfer (xfr) Menu.  
5. Press SELECT or ¤.  
Mailbox admin  
GREET PSWD QUIT  
Outbound xfr  
ADMIN  
SELECT  
QUIT  
6. Press CHNG or to turn Outbound Transfer off. Press  
Transfer: on  
CHNG  
CHNG again to turn Outbound Transfer on.  
7. Press QUIT or ® to end this session.  
Transfer: off  
CHNG  
QUIT  
P0908524 Issue 01  
Enterprise Edge Voice Messaging Reference Guide  
 
   
6 4 Transferring calls  
Enterprise Edge Voice Messaging Reference Guide  
P0908524 Issue 01  
 
Off-premise Message Notification  
10  
Introduction  
This chapter describes how to set up and change Off-premise Message Notification  
and includes the following topics:  
About Off-premise Message Notification  
You can program Enterprise Edge Voice Messaging to call you and let you know  
there is a message for you at a phone number, an extension, or a pager. The Off-  
premise Message Notification feature is enabled by your System Administrator.  
If you program Enterprise Edge Voice Messaging to call you at a telephone, you are  
prompted to enter your password before you can listen to your messages.  
You can receive notification of a message at a maximum of five different  
destination numbers assigned by you. When the number of retry attempts is reached  
for each assigned destination number, the next number in the series is called. For  
example, Enterprise Edge Voice Messaging can contact your car phone number  
first to let you know you have a message. If there is no answer, the call rings at your  
home number. If there is still no answer, the call rings at your pager number and so  
on. The number of retry attempts is assigned by your System Administrator.  
If the destination type is phone, you must assign start and stop times. The start and  
stop times apply to all five notification numbers.  
Off-premise Message Notification begins when the start time is reached. Set the  
start time for the time you will be at the destination phone number, so you are there  
to receive your calls.  
P0908524 Issue 01  
Enterprise Edge Voice Messaging Reference Guide  
 
         
6 6 Off-premise Message Notification  
Off-premise Message Notification parameters  
You can set up the parameters for Off-premise Message Notification from any  
touch tone phone. The parameters include:  
destination type (telephone, extension or pager)  
destination number (telephone, extension or pager)  
time range for receiving calls at phone numbers or extensions (Pagers are  
notified any time there is a qualifying message.)  
types of message you want to receive (all new messages, or just messages  
marked urgent)  
Note: The restrictions that apply to your telephone line also apply to Off-premise  
Message Notification numbers. For example, if you are unable to dial long  
distance phone numbers from your telephone, you cannot have a long  
distance Off-premise Message Notification destination number.  
Setting up Off-premise Message Notification to a phone number  
When you set up Off-premise Message Notification, you can add special characters  
to the destination phone number. Refer to:  
To set up Off-premise Message Notification to one phone number for the first time:  
1. Press ƒ·°⁄ to open your mailbox.  
2. Enter your mailbox password and press OK or £.  
Pswd:  
OTHR  
RETRY  
OK  
3. Press ADMIN or °.  
0 new 0 saved  
PLAY REC  
ADMIN  
4. Press to open the Off-premise Message  
Mailbox admin  
GREET PSWD QUIT  
Notification menu.  
5. Press ADMIN or to set up Off-premise Message  
Msg notify  
ADMIN  
SELECT  
Notification.  
6. Press PHONE or to choose a phone number  
Destination:  
PHONE EXT PAGER  
destination.  
7. Enter the destination phone number and press OK or  
£. The destination phone number is a maximum of  
30 digits.  
Ph:  
RETRY  
OK  
Enterprise Edge Voice Messaging Reference Guide  
P0908524 Issue 01  
 
             
Off-premise Message Notification 6 7  
8. Press OK or £ to accept the destination phone  
<x>  
ADD  
OK  
number. The <x> represents the phone number. Press  
ADD or ¤ to add special characters. For information,  
number on page 58. After you add special characters,  
press OK or £ to accept the destination number.  
9. Enter the start time for Off-premise Message  
Notification. This is a four-digit field. Any single-digit  
hour and minute must be preceded by a zero.  
Start hhmm:  
RETRY  
OK  
10. Press AM or or PM or ¤.  
<start time>  
RETRY  
AM  
PM  
OK  
OK  
11. Press OK or £ to accept the start time.  
<start time>  
RETRY  
12. Enter the time when Off-premise Message  
Notification is to stop. This is a four digit field. Any  
single-digit hour and minute must be preceded by a  
zero.  
Stop hhmm:  
RETRY  
13. Press AM or or PM or ¤.  
<stop time>  
RETRY  
AM  
PM  
OK  
14. Press OK or £ to accept the stop time.  
<stop time>  
RETRY  
15. Press NEXT or £ to accept the start time that you  
Start:<start time>  
CHNG  
NEXT  
entered. Press CHNG or to change the start time.  
Note: Steps 16 and 17 allow you to review the start  
and stop times.  
16. Press NEXT or £ to accept the stop time that you  
Stop:<stop time>  
CHNG  
NEXT  
entered. Press CHNG or to change the stop time.  
17. You can choose to be notified of all new messages or  
urgent messages only. Press OK or £ to accept the  
default message type new. This means you are notified  
whenever you receive a new message. Press CHNG or  
to change the message type to urgent. Changing  
the message type to urgent means you are notified  
only when you receive an urgent message.  
Msg type: new  
CHNG  
OK  
18. Press ® to end the session.  
Msg notify  
ADMIN  
SELECT  
P0908524 Issue 01  
Enterprise Edge Voice Messaging Reference Guide  
 
6 8 Off-premise Message Notification  
Setting up Off-premise Message Notification to an extension  
To set up Off-premise Message Notification to one extension for the first time:  
1. Press ƒ·°⁄ to open your mailbox.  
2. Enter your mailbox password and press OK or £.  
Pswd:  
OTHR  
RETRY  
OK  
3. Press ADMIN or °.  
0 new 0 saved  
PLAY REC  
ADMIN  
4. Press to open the Off-premise Message  
Mailbox admin  
GREET PSWD QUIT  
Notification menu.  
5. Press ADMIN or to set up Off-premise Message  
Msg notify  
ADMIN  
SELECT  
Notification.  
6. Press EXT or ¤ to choose an extension destination.  
Destination:  
PHONE EXT PAGER  
7. Enter the destination extension and press OK or £.  
Ext:  
RETRY  
OK  
OK  
8. Press OK or £ to accept the destination extension.  
Accept:<x>  
RETRY  
The <x> represents the extension.  
9. Enter the start time for Off-premise Message  
Notification. This is a four-digit field. Any single-digit  
hour and minute must be preceded by a zero.  
Start hhmm:  
RETRY  
OK  
10. Press AM or or PM or ¤.  
<start time>  
RETRY  
AM  
PM  
OK  
OK  
11. Press OK or £ to accept the start time.  
<start time>  
RETRY  
12. Enter the time when Off-premise Message  
Notification is to stop. This is a four digit field. Any  
single-digit hour and minute must be preceded by a  
zero.  
Stop hhmm:  
RETRY  
13. Press AM or or PM or ¤.  
<stop time>  
RETRY  
AM  
PM  
OK  
14. Press OK or £ to accept the stop time.  
<stop time>  
RETRY  
Enterprise Edge Voice Messaging Reference Guide  
P0908524 Issue 01  
 
   
Off-premise Message Notification 6 9  
15. Press NEXT or £ to accept the start time that you  
Start:<start time>  
CHNG  
NEXT  
entered. Press CHNG or to change the start time.  
Note: Steps 16 and 17 allow you to review the start  
and stop times.  
16. Press NEXT or £ to accept the stop time that you  
Stop:<stop time>  
CHNG  
NEXT  
entered. Press CHNG or to change the stop time.  
17. You can choose to be notified of all new messages or  
urgent messages only. Press OK or £ to accept the  
default message type new. This means you are notified  
whenever you receive a new message. Press CHNG or  
to change the message type to urgent. Changing  
the message type to urgent means you are notified  
only when you receive an urgent message.  
Msg type: new  
CHNG  
OK  
18. Press ® to end the session.  
Msg notify  
ADMIN  
SELECT  
P0908524 Issue 01  
Enterprise Edge Voice Messaging Reference Guide  
 
7 0 Off-premise Message Notification  
Setting up Off-premise Message Notification to a pager number  
When you set up Off-premise Message Notification, you can add special characters  
to the destination pager number. Read:  
Example of a destination pager number  
If you are assigning a pager destination number from behind a PBX or Centrex+,  
remember to insert a · (depending on your system) before the £ to access an  
outside line.  
There is a combined limit of 29 characters for the pager phone number and the pager  
message.  
For example, to reach your pager, enter:  
£›¤fififi⁄¤‹›£‹  
where:  
£ specifies the next digits are special characters  
recognizes dial tone  
¤ specifies the next digits are numbers to be dialed  
fififi⁄¤‹› is the pager phone number dialed  
inserts a timed pause  
Depending on the company supplying your paging service, the programming  
sequence may vary. For more information about setting the destination phone  
number parameters for your pager, contact your pager company.  
To set up Off-premise Message Notification to one pager number for the first time:  
1. Press ƒ·°⁄ to open your mailbox.  
2. Enter your mailbox password and press OK or £.  
Pswd:  
OTHR  
RETRY  
OK  
3. Press ADMIN or °.  
0 new 0 saved  
PLAY REC  
ADMIN  
4. Press to open the Off-premise Message  
Mailbox admin  
GREET PSWD QUIT  
Notification menu.  
5. Press ADMIN or to set up Off-premise Message  
Msg notify  
ADMIN  
SELECT  
Notification.  
6. Press PAGER or to choose a pager number  
Destination:  
PHONE EXT PAGER  
destination.  
Enterprise Edge Voice Messaging Reference Guide  
P0908524 Issue 01  
 
           
Off-premise Message Notification 7 1  
7. Enter the destination pager number and press OK or  
Pager:  
RETRY  
OK  
OK  
£.  
8. Press OK or £ to accept the destination pager number.  
The <x> represents the pager number. Press ADD or  
¤ to add special characters. If the paging service  
requires additional answer or setup time, add pause  
characters to the beginning of the pager message. For  
characters, press OK or £ to accept the destination  
number.  
<x>  
ADD  
9. Press NEXT or £ to accept the default pager message  
(represented by the xxxx). The default pager message  
sent by Enterprise Edge Voice Messaging is the  
Enterprise Edge Voice Messaging extension. This is  
the sequence of digits sent after the pager service is  
dialed (to notify you of who is paging you). Press  
CHNG or to change the pager message.  
Show:<xxxx>  
CHNG  
NEXT  
Note: There is a combined limit of 29 characters for  
the pager phone number and the pager  
message.  
10. You can choose to be notified of all new messages or  
urgent messages only. Press OK or £ to accept the  
default message type new. This means you are notified  
whenever you receive a new message. Press CHNG or  
to change the message type to urgent. Changing  
the message type to urgent means you are notified  
only when you receive an urgent message.  
Msg type: new  
CHNG  
OK  
11. Press ƒ to end the session.  
Msg notify  
ADMIN  
SELECT  
P0908524 Issue 01  
Enterprise Edge Voice Messaging Reference Guide  
 
     
7 2 Off-premise Message Notification  
Changing Off-premise Message Notification  
To change the parameters of Off-premise Message Notification refer to:  
Changing Off-premise Message Notification parameters  
To change the Off-premise Message Notification parameters from your Enterprise  
Edge telephone (assuming that you have entered a time range):  
1. Press ƒ·°⁄ to open your mailbox.  
2. Enter your mailbox password and press OK or £.  
Pswd:  
OTHR  
RETRY  
OK  
3. Press ADMIN or °.  
0 new 0 saved  
PLAY REC  
ADMIN  
4. Press to open the Off-premise Message  
Mailbox admin  
GREET PSWD QUIT  
Notification menu.  
5. Press ADMIN or to set up Off-premise Message  
Msg notify  
ADMIN  
SELECT  
NEXT  
Notification.  
6. Press CHNG or to change the destination.  
Notify:<x>  
CHNG  
Note: The <x> represents the type of destination  
(phone, extension or pager).  
7. Press PHONE or to choose a phone number  
destination. Press EXT or ¤ to choose an extension  
destination. Press PAGER or to choose a pager  
number destination.  
Destination:  
PHONE EXT PAGER  
8. Enter the destination number and press OK or £. The  
destination phone number cannot be longer than 30  
digits.  
<x>:  
RETRY  
OK  
Note: The <x> represents the type of destination  
(phone, extension or pager).  
Enterprise Edge Voice Messaging Reference Guide  
P0908524 Issue 01  
 
     
Off-premise Message Notification 7 3  
9. Press OK or £ to accept the destination number  
(represented by the <x>). Press ADD or ¤ to add  
special characters if the destination number is a phone  
or pager. For information, refer to Adding special  
you add special characters, press OK or £ to accept  
the destination number.  
Note: If you chose a phone or extension destination,  
go to step 11.  
10. Press CHNG or to change the destination and repeat  
Notify:<x>  
CHNG  
NEXT  
steps 7 to 9. Press NEXT or £ to continue.  
Note: The <x> represents the type of destination  
(phone, extension or pager).  
11. Press CHNG or to change the start time. Press NEXT  
Start:<start time>  
CHNG  
NEXT  
or £ to accept the start time.  
12. Press CHNG or to change the stop time. Press NEXT  
Stop:<stop time>  
CHNG  
NEXT  
or £ to accept the stop time.  
Note: Steps 13 and 14 allow you to review the start  
and stop times.  
13. Press CHNG or to change the message type to  
urgent. Press OK or £ to accept the new default  
message. You can choose to be notified of all new  
messages or urgent messages only. This means you are  
notified whenever you receive a new message.  
Changing the message type to urgent means you are  
notified only when you receive an urgent message.  
Msg type: new  
CHNG  
OK  
14. Press ® to end the session.  
Msg notify  
ADMIN  
SELECT  
P0908524 Issue 01  
Enterprise Edge Voice Messaging Reference Guide  
 
7 4 Off-premise Message Notification  
Changing the destination type from a pager to a telephone or extension  
To change the Off-premise Message Notification destination from a pager to a  
phone or extension (assuming that you have never entered a time range):  
1. Press ƒ·°⁄ to open your mailbox.  
2. Enter your mailbox password and press OK or £.  
Pswd:  
OTHR  
RETRY  
OK  
3. Press ADMIN or °.  
0 new 0 saved  
PLAY REC  
ADMIN  
4. Press to open the Off-premise Message  
Mailbox admin  
GREET PSWD QUIT  
Notification menu.  
5. Press ADMIN or to change Off-premise Message  
Notification. The displays show a review of the first  
destination type and destination number, followed by  
the display in step 6.  
Msg notify  
ADMIN  
SELECT  
NEXT  
6. Press CHNG or to change the destination type and  
Notify: pager  
CHNG  
the destination number.  
7. Choose the type of destination number. Press PHONE or  
to choose a phone number destination. Press EXT  
or ¤ to choose an extension destination.  
Destination:  
PHONE EXT PAGER  
8. Press OK or £ to accept the destination number. Press  
ADD or ¤ to add special characters if the destination  
number is a phone. For information, refer to Adding  
58.  
9. Press NEXT or £ to continue.  
Notify:<x>  
CHNG  
NEXT  
Note: The <x> represents the type of destination  
(telephone or extension).  
Enterprise Edge Voice Messaging Reference Guide  
P0908524 Issue 01  
 
   
Off-premise Message Notification 7 5  
Changing the destination type from phone or extension to a pager  
To change the Off-premise Message Notification destination from a phone or  
extension to a pager:  
1. Press ƒ·°⁄ to open your mailbox.  
2. Enter your mailbox password and press OK or £.  
Pswd:  
OTHR  
RETRY  
OK  
3. Press ADMIN or °.  
0 new 0 saved  
PLAY REC  
ADMIN  
4. Press to open the Off-premise Message  
Mailbox admin  
GREET PSWD QUIT  
Notification menu.  
5. Press ADMIN or to change Off-premise Message  
Notification. The displays show a review of the first  
destination type and destination number, followed by  
the display in step 6.  
Msg notify  
ADMIN  
SELECT  
NEXT  
6. Press CHNG or to change the destination type and  
Notify:<x>  
CHNG  
the destination number.  
Note: The <x> represents the type of destination  
(phone or extension).  
7. Press PAGER or to choose a pager number  
Destination:  
PHONE EXT PAGER  
destination.  
8. Press NEXT or £ to continue.  
Notify:pager  
CHNG  
NEXT  
P0908524 Issue 01  
Enterprise Edge Voice Messaging Reference Guide  
 
   
7 6 Off-premise Message Notification  
Setting up Off-premise Message Notification to more than one  
destination  
You can receive notification of a message at a maximum of five different  
destination numbers assigned by you. The following steps show you how to enter a  
phone number destination and then add a pager destination for the first time. To set  
up Off-premise Message Notification to more than one destination number:  
1. Press ƒ·°⁄ to open your mailbox.  
2. Enter your mailbox password and press OK or £.  
Pswd:  
OTHR  
RETRY  
OK  
3. Press ADMIN or °.  
0 new 0 saved  
PLAY REC  
ADMIN  
4. Press to open the Off-premise Message  
Mailbox admin  
GREET PSWD QUIT  
Notification menu.  
5. Press ADMIN or to set up Off-premise Message  
Msg notify  
ADMIN  
SELECT  
Notification.  
6. Press PHONE or to choose a destination phone  
Destination:  
PHONE EXT PAGER  
number.  
7. Enter the destination phone number and press OK or  
£. The destination phone number cannot be longer  
than 30 digits.  
Ph:  
RETRY  
OK  
OK  
8. Press OK or £ to accept the destination phone  
number. The <x> represents the phone number. Press  
ADD or ¤ to add special characters. For information,  
number on page 58. After you add special characters,  
press OK or £ to accept the destination number.  
<x>  
ADD  
9. Enter the start time for Off-premise Message  
Notification. This is a four-digit field. Any single-digit  
hour and minute must be preceded by a zero.  
Start hhmm:  
RETRY  
OK  
10. Press AM or or PM or ¤.  
<start time>  
RETRY  
AM  
PM  
OK  
11. Press OK or £ to accept the start time.  
<start time>  
RETRY  
Enterprise Edge Voice Messaging Reference Guide  
P0908524 Issue 01  
 
   
Off-premise Message Notification 7 7  
12. Enter the time when Off-premise Message  
Stop hhmm:  
RETRY  
OK  
Notification is to stop. This is a four digit field. Any  
single-digit hour and minute must be preceded by a  
zero.  
13. Press AM or or PM or ¤.  
14. Press OK or £ to accept the stop time.  
15. Press NEXT or £.  
<stop time>  
RETRY  
AM  
PM  
OK  
<stop time>  
RETRY  
Notify 2:pager  
CHNG OTHR  
NEXT  
NEXT  
16. Press NEXT or £ to continue. Press SETUP to add  
Notify 3:none  
SETUP  
another destination.  
17. Press NEXT or £ to accept the start time that you  
Start:<start time>  
CHNG  
NEXT  
entered. Press CHNG or to change the start time.  
Note: Steps 18 and 19 allow you to review the start  
and stop times.  
18. Press NEXT or £ to accept the stop time that you  
Stop:<stop time>  
CHNG  
NEXT  
entered. Press CHNG or to change the stop time.  
19. You can choose to be notified of all new messages or  
urgent messages only. Press OK or £ to accept the  
default message type new. This means you are notified  
whenever you receive a new message. Press CHNG or  
to change the message type to urgent. If you  
change the message type to urgent you are notified  
only when you receive an urgent message.  
Msg type: new  
CHNG  
OK  
20. Press ® to end the session.  
Msg notify  
ADMIN  
SELECT  
P0908524 Issue 01  
Enterprise Edge Voice Messaging Reference Guide  
 
7 8 Off-premise Message Notification  
Deleting an Off-premise Message Notification destination number  
If you have set up more than one destination number in Off-premise Message  
Notification, you are given the option to delete the destination(s). To delete an Off-  
premise Message Notification destination:  
1. Press ƒ·°⁄ to open your mailbox.  
2. Enter your mailbox password and press OK or £.  
Pswd:  
OTHR  
RETRY  
OK  
ADMIN  
QUIT  
3. Press ADMIN or °.  
0 new 0 saved  
PLAY REC  
4. Press to open the Off-premise Message  
Mailbox admin  
GREET PSWD  
Notification menu.  
5. Press ADMIN or to set up Off-premise Message  
Msg notify  
ADMIN  
SELECT  
NEXT  
Notification.  
6. Press OTHR if you want to delete the first destination,  
or press NEXT or £ to scroll through the destinations  
until you find the destination that you want to delete.  
When you find the destination that you want to delete,  
press OTHR.  
Notify 1:<x>  
CHNG  
OTHR  
Note: The <x> represents the type of destination  
(phone, extension or pager).  
7. Press DEL to delete the first destination number.  
Notify 1:<x>  
DEL INS  
QUIT  
NEXT  
8. The first destination number is deleted. The Notify 2  
destination changes to become the Notify 1  
destination number.  
Notify 1:<x>  
CHNG OTHR  
Note: To delete more destination numbers, press  
OTHR and repeat steps 6 and 7. When you are  
done deleting destination numbers, press ®  
to end this session.  
Enterprise Edge Voice Messaging Reference Guide  
P0908524 Issue 01  
 
   
Off-premise Message Notification 7 9  
Inserting an Off-premise Message Notification destination number  
You have the option to insert destination number(s) if you have more than one  
destination number. To insert an Off-premise Message Notification destination:  
1. Press ƒ·°⁄ to open your mailbox.  
2. Enter your mailbox password and press OK or £.  
Pswd:  
OTHR  
RETRY  
OK  
3. Press ADMIN or °.  
0 new 0 saved  
PLAY REC  
ADMIN  
4. Press to open the Off-premise Message  
Mailbox admin  
GREET PSWD QUIT  
Notification menu.  
5. Press ADMIN or to set up Off-premise Message  
Msg notify  
ADMIN  
SELECT  
NEXT  
Notification.  
6. Press OTHR to insert a new destination number in the  
first Off-premise Message Notification position  
(Notify 1), or press NEXT to scroll through the  
destinations until you find the destination position that  
you want to replace, and then press OTHR.  
Notify 1:<x>  
CHNG OTHR  
Note: The <x> represents the type of destination  
(phone, extension or pager).  
7. Press INS to insert a destination number.  
Notify 1:<x>  
DEL  
INS  
QUIT  
NEXT  
Note: The <x> represents the type of destination  
(phone, extension or pager).  
8. Press SETUP to set up a new destination number, and  
Notify 1:none  
SETUP  
Note: When you are done inserting destination  
numbers, press ® to end this session.  
P0908524 Issue 01  
Enterprise Edge Voice Messaging Reference Guide  
 
   
8 0 Off-premise Message Notification  
Turning Off-premise Message Notification on and off  
You can turn Off-premise Message Notification on or off at any time. When you  
turn Off-premise Message Notification off, you do not affect any of the assigned  
you turn Off-premise Message Notification is on, you are notified whenever you  
receive a message during the time you specified.  
To turn Off-premise Message Notification on and off:  
1. Press ƒ·°⁄ to open your mailbox.  
2. Enter your mailbox password and press OK or £.  
Pswd:  
OTHR  
RETRY  
OK  
ADMIN  
QUIT  
3. Press ADMIN or °.  
0 new 0 saved  
PLAY REC  
4. Press to open the Off-premise Message  
Mailbox admin  
GREET PSWD  
Notification menu.  
5. Press SELECT or ¤.  
Msg notify  
ADMIN  
SELECT  
OK  
6. Press CHNG or to turn Off-premise Message  
Notify on  
CHNG  
TIME  
Notification off if it is on (as shown).  
7. Press OK or .  
Notify off  
CHNG  
TIME  
OK  
Note: Press TIME to review the start and stop time  
parameters.  
8. Press ® to end the session.  
Mailbox admin  
GREET PSWD QUIT  
A person who receives an Off-Premise Message Notification call can cancel Off-  
premise Message Notification to their destination number. This is useful if a  
destination is incorrectly programmed and a wrong party receives the calls. The  
recipient of an Off-premise Message Notification call hears the following voice  
prompt: “Message for (name of mailbox owner). To log in press . If you have  
received this call by mistake, please press ¤.  
Enterprise Edge Voice Messaging Reference Guide  
P0908524 Issue 01  
 
     
Recording a call  
11  
Introduction  
ƒ·°· allows you to record an active telephone call and place the  
resulting message in your mailbox. Before you activate the Call Record feature, ask  
the parties on the call for permission to record the call.  
The maximum length of the Call Record message is determined by the Class of  
Service setting for your incoming message length. If the mailbox message length is  
surpassed, the voice prompt “Recording stopped. The recording limit has been  
reached” plays and the recording ends. After Call Record stops, you can re-activate  
ƒ·°· to start another record call session. The call is recorded in two  
separate messages if this occurs. Ask your System Administrator for the message  
length that is assigned to your mailbox.  
Note: Call Record is not enabled by default. The System Administrator must  
enable this feature by assigning you a Class of Service that supports Call  
Record. In some areas Call Record is not available as it contravenes local  
laws. Ask your System Administrator about the availability of Call Record  
in your area.  
Using Call Record  
After a call is recorded, Enterprise Edge Voice Messaging places the recorded call,  
as a message, in the mailbox associated with the extension that activated the Call  
Record feature. The call includes alternate extensions associated with the mailbox.  
The Call Record message can be forward to other mailboxes. For more information  
on forwarding messages, refer to Forwarding a copy of a message to one or more  
To record a call:  
1. While on an active call, press ƒ·°·.  
Other parties on the call may hear hold tones while the  
system conferences in Enterprise Edge Voice  
Messaging.  
Before the call begins recording, the prompt “This call  
is being recorded” plays to all the parties on the call  
and then a recording tone plays.  
2. Press QUIT to stop the call recording. The Call Record  
message is left in your mailbox.  
Recording  
PAUSE  
QUIT  
Press PAUSE to suspend the call recording. Press  
RESUME to continue call recording or press QUIT to  
stop the call recording.  
If the message is stopped, all the parties on the call  
hear “Recording stopped”.  
P0908524 Issue 01  
Enterprise Edge Voice Messaging Reference Guide  
 
       
8 2 Recording a call  
Enterprise Edge Voice Messaging Reference Guide  
P0908524 Issue 01  
 
Enterprise Edge Voice Messaging Tips  
12  
Introduction  
This chapter describes some easy to follow guidelines to optimize using Enterprise  
Edge Voice Messaging.  
Enterprise Edge Voice Messaging Tips  
To take advantage of Enterprise Edge Voice Messaging and its many features:  
Listen to your messages frequently. Answer your messages promptly to  
encourage callers to use Enterprise Edge Voice Messaging and reassure them that  
it is as reliable as speaking with you personally.  
You do not have to be at your desk to play your messages. When you are away from  
your desk, you can play your messages from any touch tone phone.  
Clean up your mailbox. There is limited storage in your mailbox and within  
Enterprise Edge Voice Messaging. Do not save messages unless you need to listen  
to them again. When you are finished with a message, erase the message to free  
storage space for yourself and other mailbox owners.  
Keep a record of your password in a secure place. Treat your Enterprise Edge  
Voice Messaging password as a secret code. Write down your password and keep  
it in a safe place. Do not keep your password near your telephone. If you let  
someone else have temporary access to your mailbox, change your password  
afterwards. If you forget your password, the System Administrator can reset it to the  
default password 0000. You can then enter a new password.  
When sending messages, make them brief and to the point. More than 75% of  
the time spent on a normal business telephone call consists of making small talk,  
pleasantries and other socializing. Sending a message rather than making a call can  
save you time. Try to avoid sounding hurried or rude while restricting your  
messages to the essentials.  
Change your Primary greeting frequently. It is a good idea to change your  
Primary greeting on a regular basis. Change your greeting to indicate that you listen  
to your messages and maintain your mailbox on a regular basis. Change your  
Primary greeting to provide a personal touch that frequent callers appreciate.  
Make your Alternate greeting specific. Choosing an Alternate greeting usually  
means you are away from the office. If you are out of the office, indicate in your  
Alternate greeting when you expect to return. If you check your mailbox even  
though you are out of the office, make that clear. If callers can reach you at another  
phone number, ensure that your message includes the phone number and the time  
period of the temporary arrangement. If you are going to be out of the office,  
remember to forward your telephone to Enterprise Edge Voice Messaging.  
P0908524 Issue 01  
Enterprise Edge Voice Messaging Reference Guide  
 
           
8 4 Enterprise Edge Voice Messaging Tips  
Extended Absence Greeting. Begin this greeting by announcing your vacation or  
travel plans. This gets the attention of the caller. For example, “Vacation alert! Hi,  
this is Marshall. I will be on vacation starting on the 5th, and I will be returning to  
work on the 12th. If you care to do so, please leave a message and I will return your  
call when I return from vacation. For immediate assistance, please press zero.”  
Record your greetings and messages clearly. For a better quality recording, speak  
directly into the handset. Do not use the Handsfree feature. Remember to speak  
clearly with a pleasant voice at a pace that is easy to understand. Do not speak too  
softly or loudly or make the greeting or message too lengthy. After you record a  
greeting or message play it back. Make sure that your greeting or message sounds  
the way you want it to before you accept it.  
Do not forget to use the Copy and Reply features. You can use Enterprise Edge  
Voice Messaging to send copies of messages to other mailboxes and reply to  
messages with a message of your own. When you send copies of messages to other  
people, ensure that your introduction explains why you are forwarding a copy of the  
message. Is the copy for information only? Is the message meant for the person to  
whom you are forwarding it? Who is responsible for the action on the message?  
Use Group Lists for multiple copies of messages. If you find that you regularly  
send the same message to several different people, ask the System Administrator to  
create a Group List for you. With a Group List, you can send the same message to  
all the mailboxes in the Group List.  
Encourage Enterprise Edge Voice Messaging use. Old habits are sometimes hard  
to break, and some people have difficulty accepting or even trying new  
technologies. Use your Personal mailbox and other Enterprise Edge Voice  
Messaging features, and encourage your co-workers and frequent callers to use  
them too.  
Report problems promptly. If you encounter problems using Enterprise Edge  
Voice Messaging, report the trouble to the System Administrator as soon as  
possible.  
Enterprise Edge Voice Messaging Reference Guide  
P0908524 Issue 01  
 
Troubleshooting  
13  
Introduction  
This chapter describes some problems that can occur while you are using Enterprise  
Edge Voice Messaging. This chapter includes a list of typical problems and what to  
do when they occur.  
The problems you encounter while using Enterprise Edge Voice Messaging are  
usually operating problems. Sometimes a difficulty occurs that indicates a system  
problem with the Enterprise Edge server. If events occur that are not covered in this  
chapter, report them to your System Administrator immediately.  
The Automated Attendant transfers some callers to the General Delivery Mailbox.  
Enterprise Edge Voice Messaging requires a tone signal and a minimum voice  
level. If a response is not received, the caller is automatically transferred by the  
Automated Attendant to the Enterprise Edge Voice Messaging operator. If the  
operator is not available, the call transfers to the General Delivery mailbox.  
Possibly the extension called does not have a mailbox assigned to it. Ask your  
System Administrator to verify that the mailbox is assigned to the extension  
Feature 981 produces a LOG prompt on my Enterprise Edge display.  
Whenever the Log: prompt appears on the display, it can be caused by:  
Possibly the extension you are using does not have an operating mailbox. If the  
extension does not have a mailbox, Enterprise Edge Voice Messaging requests  
both a mailbox number and a password.  
A Guest mailbox that normally does not have an assigned extension. Ask your  
System Administrator to verify that your extension is properly assigned to your  
mailbox.  
My telephone cannot be forwarded to Enterprise Edge Voice Messaging.  
If you are attempting to forward your extension to Enterprise Edge Voice  
Messaging and the display shows Not in service you might be forwarding to the  
wrong extension number. Use feature code 985 to verify you are calling the correct  
Enterprise Edge Voice Messaging extension number.  
My mailbox is not accepting messages.  
A mailbox accepts messages only after the mailbox is initialized. A mailbox cannot  
receive messages until it is initialized by the mailbox owner. Initialize your  
mailbox. Refer to the Enterprise Edge Quick Reference Guide or to Chapter 3 of  
this guide.  
P0908524 Issue 01  
Enterprise Edge Voice Messaging Reference Guide  
 
         
8 6 Troubleshooting  
My name is not played in the Company Directory.  
Check to ensure that your mailbox is initialized. If it is not initialized, your name is  
not played in the Company Directory and your mailbox cannot receive any  
messages. If you have recorded your Company Directory name, ask your System  
Administrator to ensure that the Company Directory Override is set to YES.  
I have forgotten my mailbox password.  
A forgotten password cannot be recovered. Your old password must be reset to the  
default password of four zeros (0000). After the System Administrator has reset  
your password, you must open your mailbox and change the default password.  
I attempt to access my mailbox and I hear the recording: This mailbox has been locked to  
prevent unauthorized access. Please contact your administrator for assistance.”  
Your mailbox is assigned a maximum number of incorrect password attempts.  
Enterprise Edge Voice Messaging records the number of incorrect attempts from  
the last time your mailbox was successfully accessed. After the number is passed  
you are “locked-out”. Your mailbox cannot be opened again until the System  
Administrator resets the password.  
Enterprise Edge Voice Messaging Timeout  
The Enterprise Edge Voice Messaging Timeout feature allows five seconds for you  
to choose an option. If Enterprise Edge Voice Messaging does not detect a  
selection, the Automated Attendant replays the option list. If an option is still not  
selected, Enterprise Edge Voice Messaging ends the session.  
Enterprise Edge Voice Messaging has minimum voice level detection. If Enterprise  
Edge Voice Messaging does not detect an audio signal, it requests the caller to  
speak louder and provides the option to re-record. If no voice level is detected after  
the prompt, Enterprise Edge Voice Messaging ends the session.  
Messages are cut off  
If people need to leave long messages in your mailbox (up to 10 minutes), you can  
ask the System Administrator to give you more message recording storage space.  
I attempt to listen to my messages and I hear the recording: “Your mailbox is full. You must  
erase some messages before you can listen to new messages.”  
Your mailbox is equipped with the Never Full Mailbox feature, which allows a  
caller to leave a message in your mailbox, even if the mailbox is “full”. The  
message is stored, but cannot be accessed until you delete at least one saved  
message. If you find that you need more message time in your mailbox, ask your  
System Administrator to give you more storage space.  
Wrong prompt language  
If the wrong language appears on the display of your Enterprise Edge telephone, ask  
the System Administrator to change this.  
Enterprise Edge Voice Messaging Reference Guide  
P0908524 Issue 01  
 
           
Troubleshooting 8 7  
Outbound Transfer does not work.  
Ensure that you have recorded the correct instructions for callers in your personal  
greeting. In your greeting, tell callers to press to reach you. Refer to Outbound  
Ensure that the destination number you enter is not restricted. For example, if you  
cannot call long distance numbers from your telephone, then you cannot set up  
Outbound Transfer to a long distance number.  
Check to see if Outbound Transfer is turned on. Refer to Turning Outbound  
Off-premise Message Notification does not work  
If Off-premise Message Notification does not work, ask the System Administrator  
to check the Off-premise Message Notification parameters. Also, ask the System  
Administrator to check if you are allowed to have Off-premise Message  
Notification. Ensure that the destination phone number and time parameters are  
correct.  
Ensure that the destination number(s) that you enter are not restricted. For example,  
if you cannot call long distance numbers from your telephone, then you cannot set  
up Off-premise Message Notification to a long distance number.  
Check to see if Off-premise Message Notification is turned on. Refer to Turning  
P0908524 Issue 01  
Enterprise Edge Voice Messaging Reference Guide  
 
 
8 8 Troubleshooting  
Enterprise Edge Voice Messaging Reference Guide  
P0908524 Issue 01  
 
Appendix A:  
Default values and tone commands  
Default mailbox numbers for the General Delivery mailbox  
s
Mailbox number  
length  
Default General  
Delivery Mailbox  
number  
2
3
4
5
6
7
10  
100  
1000  
10000  
100000  
1000000  
If the Group List leading digit is one then the default General Delivery mailbox  
numbers begin with two.  
DTMF tone commands for setting up Off-premise Message Notification  
Option function  
Dialpad button  
Review number  
¤
£
Enter more digits  
Insert a timed pause (4 sec)  
Recognize dial tone (1.5 sec)  
Insert a # button tone  
Insert a * button tone  
Accept number  
Cancel and re-enter  
If Enterprise Edge Voice Messaging is installed with PBX or Centrex+ and you  
want to access an outside line, you must enter the command to recognize a dial tone.  
For example, enter · to access an outside line, press £ and then to recognize  
dial tone and then press ¤ to enter more digits. Enter the destination number, press  
£ and any required pauses. Each pause entered is four seconds long. For  
definitions of Pause, Recognize dial tone and Enter more digits, refer to the  
Glossary.  
P0908524 Issue 01  
Enterprise Edge Voice Messaging Reference Guide  
 
           
9 0 Appendix A: Default values and tone commands  
Enterprise Edge Voice Messaging Reference Guide  
P0908524 Issue 01  
 
Glossary  
Administration  
The tasks involved in maintaining the Enterprise Edge Voice Messaging mailboxes,  
greetings and set up configuration.  
Alternate greeting  
A greeting recorded for a Personal mailbox and played on occasions such as  
absence, illness, or vacation.  
Attendant sign On/ Off  
The task performed by a company receptionist or Operator that indicates to  
Enterprise Edge Voice Messaging when an Operator is available to answer calls.  
Automated Attendant  
The Enterprise Edge Voice Messaging answering service that answers incoming  
calls with a Company greeting, plays a list of Enterprise Edge Voice Messaging  
options to a caller and performs call routing functions in response to a caller’s  
dialpad selections.  
Broadcast Message  
A message that can be sent only by the System Administrator. This type of message  
plays in all initialized Personal mailboxes and plays immediately after the mailbox  
is opened. It is automatically erased after the mailbox owner listens to the message.  
Business Status  
A Enterprise Edge Voice Messaging setting that tells Enterprise Edge Voice  
Messaging whether a company is closed or open for business.  
Class of Service  
A predetermined number designation that specifies the Enterprise Edge Voice  
Messaging Options for a mailbox.  
Company Directory  
An internal voice list that contains the names of users with initialized mailboxes  
designated to appear in the Company Directory.  
Conventions  
The way certain information is described. For example, using underlined text to  
represent second-line display prompt information.  
Default  
The parameters preset in the Enterprise Edge Voice Messaging system.  
P0908524 Issue 01  
Enterprise Edge Voice Messaging Reference Guide  
 
   
9 2 Glossary  
Designated Operator  
An individual in a company who is assigned to answer the Enterprise Edge Voice  
Messaging Operator Request option.  
Display  
A one-line or two-line screen on an Enterprise Edge telephone that shows  
Enterprise Edge Voice Messaging commands and options.  
Display buttons  
The three buttons that appear on an Enterprise Edge two line display display. When  
pressed, these buttons select the specified Enterprise Edge Voice Messaging option.  
Display options  
The choices available to a user that appear on an Enterprise Edge two line display  
display. Options appearing on the display can be selected using the display or  
dialpad buttons  
Enterprise Edge ATA 2  
An Enterprise Edge product that allows you to connect an analog device, such as a  
single-line telephone or a facsimile machine, to an Enterprise Edge Voice  
Messaging system.  
Envelope information  
A date and time stamp that appears on all messages left in a mailbox. If the message  
is left by another mailbox owner, envelope information includes the message  
sender’s name.  
Extension  
A two-digit to seven-digit number used to reach a designated telephone. Also an  
Enterprise Edge internal telephone.  
Feature code  
A unique three-digit code used to access Enterprise Edge Voice Messaging features  
and options.  
General Delivery mailbox  
One of the two Special mailboxes used to collect messages for individuals in a  
company who have not been assigned a Personal mailbox.  
Greetings  
There are three types of Enterprise Edge Voice Messaging greetings: Company  
greetings, Personal mailbox greetings and Information greetings. Company  
greetings play by the Automated Attendant to incoming callers. Personal mailbox  
greetings play to callers who want to leave a message in the selected mailbox.  
Information mailbox greetings play to describe goods or services available to  
callers.  
Enterprise Edge Voice Messaging Reference Guide  
P0908524 Issue 01  
 
Glossary 9 3  
Group Lists  
A collection of mailbox numbers assigned to a special group name and number by  
the System Administrator. If a message is sent to a Group List, all mailboxes  
contained in the list receive the same message.  
Guest mailbox  
A mailbox assigned to a user who does not have an extension.  
Information mailbox  
A mailbox that provides a caller with a message describing goods or services  
available from your company.  
Initialize mailbox  
Preparing a mailbox to receive messages, which includes changing a mailbox  
default password and recording a Company Directory name.  
Leave Message  
The feature code used to leave messages in Enterprise Edge Voice Messaging  
mailboxes.  
Mailbox  
A storage place for voice messages on the Enterprise Edge Voice Messaging  
system.  
Mailbox number length  
The number of digits allowed in a mailbox number. The mailbox number length  
ranges from two to seven digits.  
Mailbox overrides  
Mailbox overrides are optional parameters in addition to the Class of Service  
values. The mailbox overrides are: Include in Company Directory, Alternate  
Extensions, Fax line (virtual), Call Screening, Message Waiting Notification and  
Outdial route.  
Message Delivery options  
Message sending options stamped onto a message. There are five Message Delivery  
Options: Normal, Certified, Urgent, Private and Timed. A Message Delivery  
Option can be assigned to a message after it has been recorded.  
Message Waiting Notification  
A display prompt that informs a mailbox owner when a message has been left in a  
mailbox. This feature is a mailbox override.  
P0908524 Issue 01  
Enterprise Edge Voice Messaging Reference Guide  
 
9 4 Glossary  
Never Full mailboxes  
Your Enterprise Edge Voice Messaging mailbox is equipped with the Never Full  
mailbox feature, which allows an external caller to leave a message in your  
mailbox, even if the mailbox is “full”. The message will be stored, but cannot be  
accessed until you delete at least one saved message.  
Off-premise Message Notification  
The Enterprise Edge Voice Messaging feature that calls destination numbers that  
you set up, to let you know you have a new or urgent message. This feature is a part  
of the Class of Service.  
Operator Status  
The Enterprise Edge Voice Messaging indicator that determines if a company’s  
receptionist or Designated Operator is available.  
Option  
A Enterprise Edge Voice Messaging choice that is given to a user through voice or  
display prompts.  
Password  
A four- to eight-digit number that is entered on the dialpad. A password is used to  
open mailboxes or perform configuration tasks.  
Pause  
Pause is used when setting up pager notification. Each pause entered is  
automatically four seconds. For voice pagers, pauses are entered after the pager  
number to delay the start of the Enterprise Edge Voice Messaging voice prompt that  
activates the pager. For alphanumeric pagers, pauses are entered after the pager  
number and before the digits that appear on the pager display.  
Personal mailboxes  
Mailboxes assigned to users as a place to store messages.  
Primary greeting  
The main greeting played in a Personal mailbox.  
Programmable memory buttons  
Buttons on the Enterprise Edge one line and two line display telephones that can  
store feature codes and numbers.  
Recognize dial tone  
After accepting the Outbound Transfer or Off-premise Message Notification  
destination phone number, entering adds a D to the digit string. The Enterprise  
Edge system uses this to recognize dial tone when an access code is required.  
Enterprise Edge Voice Messaging Reference Guide  
P0908524 Issue 01  
 
Glossary 9 5  
Resetting passwords  
A System Administrator task that changes a mailbox password from its current  
setting back to the Enterprise Edge Voice Messaging default setting 0000 (four  
zeros).  
Special mailboxes  
The two mailboxes used by the System Administrator and designated Enterprise  
Edge Voice Messaging Operator. The two Special mailboxes are System  
Administrator and General Delivery.  
System Administrator  
The person responsible for configuring, updating, and maintaining the Enterprise  
Edge Voice Messaging system.  
System Administrator mailbox  
One of the two Special mailboxes. This mailbox is used by the System  
Administrator for sending Broadcast Messages. This is also the System  
Administrator’s Personal mailbox.  
Touch tone phone  
A push-button telephone that emits DTMF tones.  
Voice prompts  
The prerecorded voice instructions that play when you access the different  
Enterprise Edge Voice Messaging features and options.  
P0908524 Issue 01  
Enterprise Edge Voice Messaging Reference Guide  
 
9 6 Glossary  
Enterprise Edge Voice Messaging Reference Guide  
P0908524 Issue 01  
 
Index  
Certified Message Delivery option 44  
Changing  
A
Activating  
Off-premise Message Notification  
parameters 72  
Outbound Transfer  
Call Forward with Caller ID 51  
Outbound Transfer 63  
Adding special characters  
pause characters 71  
to a destination number 58  
Alert tone 52  
Alternate greeting 28, 83  
choosing whether mailbox accepts  
messages 31  
destination number 62  
parameters 62  
your mailbox password 18  
your name in the Company Directory 19  
Character limit  
for Off-premise Message Notification  
destination pager number and message  
using 31  
Alternate Language 13  
Assigning  
for Off-premise Message Notification  
destination number 71  
Message Delivery options 42  
Personalized greeting 32  
Assigning a Target Attendant  
overrides routing to Operator 20  
Automated Attendant 39, 57, 85  
transferring to 57  
Automatic disconnection from Information  
message 29  
B
Broadcast messages 44  
C
Call Forward on Busy  
overrides Caller ID 53  
Call Forward with Caller ID  
activating 51  
for Outbound Transfer  
destination pager number 58  
destination telephone number 58  
Choosing the Primary or Alternate greeting 31  
Company Directory 13, 19, 42, 86  
changing your name in 19  
recording your name in 15  
removing a name from 19  
Company Directory name 27, 29  
Copying a message 36  
to other recipients 50  
using ALL 50  
using CC 50  
Custom Call Routing (CCR) 57  
transferring calls to 57  
Custom feature codes 23  
canceling 51  
Call Record 81  
Call Screening  
D
Default feature codes 21  
Default pager message 71  
Default password 15, 18  
Default values and tone commands 89  
Default values for Special Mailboxes 89  
Deleted messages, retrieving 38  
Deleting  
purpose 39  
when unavailable 39  
interaction with Call Forward on Busy 53  
Calls  
interrupting 22, 52  
transferring  
Personalized greeting 33  
Deleting messages 36  
to CCR 57  
Destination number  
to Enterprise Edge Voice Messaging 55  
to General Delivery mailbox 35  
to Operator 35  
character limit 71  
for pagers 70  
special characters in 58  
when Enterprise Edge Voice Messaging is  
behind PBX or Centrex  
to receptionist 35  
Canceling  
Call Forward with Caller ID 51  
Outbound Transfer 63  
CCR Information message 57  
used to access an outside line 70  
Destination pager number  
character limit 58, 70  
P0908524 Issue 01  
Enterprise Edge Voice Messaging Reference Guide  
 
 
98 Index  
Destination telephone number  
character limit 58  
Directory number sent as default pager message  
Information 29, 34  
Personal 16, 27  
Personalized 28  
assigning 32  
available with Caller ID 28  
deleting 33  
recording 32  
Primary 28, 83  
example 28  
Displaying feature codes 23  
E
Entering a destination number 58  
Entering characters  
on command line 11  
purpose 28  
recording  
Enterprise Edge ATA 2  
has no feature button 11  
no Message Waiting Notification capability  
Enterprise Edge one-line display telephones  
using 9  
using the dialpad to make selections 9  
Enterprise Edge two-line display telephones,  
using 10  
Enterprise Edge Voice Messaging  
default password 15  
Alternate 29  
Primary 29  
types of 27  
Group List 41  
name 49  
sending messages to 41  
Group message  
using a Group List 41  
Guest mailboxes 14  
no operating extension for 14  
Guide, organization 7  
H
display 11  
how callers reach 35  
transferring calls to 55  
using  
Hold tone 39  
Home menu 57  
with touch tone telephone 35  
using with rotary dial telephone 35  
Erasing messages 36  
I
Information greeting  
example 29, 34  
purpose 29, 34  
Etiquette, telephone 81, 83  
F
Information message  
automatic disconnection from 29  
CCR 57  
Initializing your mailbox 15  
Internal messages, replying to 48  
Interrupting calls 22, 52  
Interrupting voice prompts 9, 10, 12  
L
Feature 980 42  
Feature 981 42  
Feature 985 11  
Feature 986 55, 56, 57  
Feature 987 52  
Feature 988 44  
Feature codes 19  
default 21  
Language, Alternate 13  
Leave Message feature 11, 42, 46, 47  
Listening to your messages. see Playing your  
mailbox messages  
M
Mailbox  
displaying 23  
programming 24  
table of 23  
Forwarded messages  
recording an introduction for 50  
Full mailbox 35  
G
full 35  
initializing 15  
General Delivery mailbox 35  
purpose 14  
used when Personal mailbox not available  
Mailboxes  
Greetings  
General Delivery  
purpose 14  
Guest 14  
Alternate 28, 83  
using 31  
Information 14  
Enterprise Edge Voice Messaging Reference Guide  
P0908524 Issue 01  
 
Index 99  
Personal 13  
Special 14  
User 13  
O
Off-premise Message Notification  
activated by interrupted message 22  
changing parameters 72  
destination number  
Making selections using the dialpad  
with Enterprise Edge one-line display  
telephones 9  
character limit 71  
Memory buttons 21  
Menu, Home (CCR) 57  
Message Delivery options  
assigning 42  
destination pager number and message  
character limit 70  
feature restrictions 66  
not working 87  
Certified 44  
Normal 44  
Private 44  
Timed Delivery 44  
Urgent 44  
setting up  
to a pager number 70  
to a telephone number 66  
to an extension number 68  
stopping unwanted 80  
Off-premise Message Notification parameters  
destination telephone number 66  
destination type 66  
Message Waiting Notification  
not available with Enterprise Edge ATA 2  
Messages  
time range 66  
addressed to a Group List 41  
Broadcast 44  
types of message 66  
Open Mailbox feature 11, 42, 45, 46  
Opening your mailbox  
remotely 17  
copying 36, 50  
using ALL 50  
using CC 50  
Operator 13  
cut off 86  
deleted, retrieving 38  
deleting 36  
erasing 36  
Group 41  
left in General Delivery mailbox 14  
playing 36  
transferring to 57  
Optimizing Outbound Transfer 60  
Organization, guide 7  
Outbound Transfer  
activating 63  
canceling 63  
destination pager number  
character limit 58  
destination telephone number  
character limit 58  
pausing 37  
rewinding 36  
skipping forward 36  
skipping to end 36  
the Envelope 36  
volume control 37  
playing the next 37  
playing the previous 37  
Private, cannot copy 50  
quitting 37  
setting up  
to a telephone number 61  
to an extension number 6162  
P
Password 86  
“locked-out” 86  
changing 18  
default 18  
recording 42  
Pause characters, adding 71  
Pausing a message 37  
Personal greetings 16, 27  
example 20  
replaying 37  
replying to 37, 48  
saving 37  
sending 42  
recording technique 27  
Personal Mailbox  
Guest 13  
sending to multiple recipients 42  
N
Name  
User 13  
recording in Company Directory 15  
removing from Company Directory 19  
Never Full mailbox feature 35  
Normal Message Delivery option 44  
Personal messages addressed to a Group List  
P0908524 Issue 01  
Enterprise Edge Voice Messaging Reference Guide  
 
100 Index  
Personalized greeting 28  
assigning 32  
Outbound Transfer  
to a telephone number 61  
to an extension number 6162  
deleting 33  
recording 32  
Play order of messages 44  
Playing the message Envelope 36  
Playing your mailbox messages 36  
Prerequisites, for using guide 7  
Primary greeting 28, 83  
Primary or Alternate greeting  
choosing 31  
Skipping forward in messages 36  
Skipping forward to end of messages 36  
Special characters  
in destination number 58  
Special mailboxes  
General Delivery 14  
System Administrator 14  
Stopping unwanted Off-premise Message  
Notification 80  
Private Message Delivery option 44  
no forwarding with 44  
Private messages  
T
cannot copy 50  
Target Attendant, assigning 20  
Timed Message Delivery option 44  
Timeout 86  
Transfer 57  
Transferring  
not forwarded 44  
Programming a memory button  
to a feature code 24  
Prompt language, wrong 86  
R
to Operator 57  
Recording  
to the Automated Attendant 57  
Transferring calls  
Alternate greeting 29  
Personalized greeting 32  
Primary greeting 29  
to CCR 57  
to Enterprise Edge Voice Messaging 55  
to General Delivery mailbox 35  
to Operator 35  
your name in the Company Directory 19  
Recording a call 81  
Recording messages 42  
Recording technique  
Personal greetings 27  
Replaying messages 37  
Reply feature 38  
to receptionist 35  
Troubleshooting 85  
Types 27  
Types of greeting 27  
U
Replying 48  
Urgent Message Delivery option 44  
Urgent messages  
Play order of messages 44  
User mailboxes 13  
V
Voice prompts 11, 44, 51  
interrupting 9, 10, 12  
on an Enterprise Edge one-line display  
telephone 12  
to an external message sender  
using the DIAL option 49  
to an internal message sender 48  
using the CALL option 48  
using the MSG option 48  
to messages 37, 48  
Retrieving deleted messages 38  
Rewinding messages 36  
Routing messages from General Delivery  
mailbox 14  
Volume control 37  
S
Saving messages 37  
Sending messages 42  
to a Group List 41  
to multiple recipients 42  
Setting up  
Off-premise Message Notification  
to a pager number 70  
to a telephone number 66  
to an extension number 68  
Enterprise Edge Voice Messaging Reference Guide  
P0908524 Issue 01  
 

MTD Lawn Mower 110 530A User Manual
MTX Audio Car Speaker F 150 SUPERCREW User Manual
Navigon GPS Receiver 21xx max User Manual
Nikon Camera Accessories 360TM User Manual
Nortel Networks Telephone Regular Telephone User Manual
Omega Thermometer OS642C LS User Manual
Oregon Scientific Thermometer RMR682A User Manual
Panasonic Digital Camera AJ D610WA User Manual
Panasonic Drill EY7460 User Manual
Panasonic Power Supply LC XC1238AP User Manual